Local • Family-Owned
GE Repair in Arvada, CO
From a quiet ice bin to a range that won't light, we test your GE where it sits and price it firmly before any part changes.
We repair every GE appliance
- $85 DiagnosticCredited toward your repair
- 90-Day WarrantyParts & labor
- Open 24/7Same-day service often available
- Local & Family-OwnedBased in Superior
GE Repair • Arvada
Neighborly Repair for GE, Profile and Café Owners
When Arvada customers book a GE repair with PointLine, the visit begins at our single family-run office at 2600 S Rock Creek Pkwy #103 in Superior, just a short drive from your home. We are an independent company, not part of GE Appliances, and we work on standard GE models along with the GE Profile and Café lines. That covers the full house, from the refrigerator humming in the kitchen to the dryer tumbling in the basement. You get a technician who shows up with a meter, a flashlight and the patience to explain what failed.
GE appliances do a lot of quiet thinking. Sensors report temperatures, water levels and motor speeds, and a control board decides what to do with every reading, so a single bad thermistor can make a perfectly healthy board look guilty. Swapping parts until the symptom disappears is the expensive way to fix one of these machines, and it leaves you guessing about what will fail next. We test first, name the actual cause, and give you a firm quote before any work begins.
GE Appliances
GE Appliances From Pantry to Laundry Room
Here is what typically goes wrong with each GE appliance we service, including Profile and Café versions, and what your technician checks first.
GE Refrigerator
A GE refrigerator that runs warm usually traces back to frost on the evaporator, a stalled fan, dusty condenser coils or a sensor sending the wrong number to the board. We measure temperatures in both sections, inspect the coil and test the defrost parts before deciding anything.
GE refrigerator repair in ArvadaGE Freezer
Freezers tend to fail quietly, with soft ice cream or thick frost along the back wall as the first clue. We check door seals, the defrost heater and termination sensor, the evaporator fan and the start components on the compressor.
GE freezer repair in ArvadaGE Ice Maker
When the bin stays empty, the cause can be a frozen fill tube, a clogged water filter, a weak inlet valve or an ice maker module that no longer cycles. We follow the water from the supply line to the tray and confirm each stop is doing its job.
GE ice maker repair in ArvadaGE Washer
GE washers that won't drain, spin or finish a cycle often have a blocked pump, a lid or door lock that isn't reporting, or worn suspension parts. We open the pump area, test the lock signal at the control and check the drive system under load.
GE washer repair in ArvadaGE Dryer
A dryer that runs cold or takes forever usually points to a restricted vent, a blown thermal fuse, an open heating element or a tired gas igniter. We check airflow at the outside hood and test each safety device and heat source in turn.
GE dryer repair in ArvadaGE Dishwasher
Dirty dishes, standing water and leaks at the door are the usual complaints on a GE dishwasher. We clean and inspect the filter and spray arms, test the inlet valve and drain pump, and look closely at the door gasket and tub seals.
GE dishwasher repair in ArvadaGE Oven
Slow preheats, uneven baking and missed set temperatures generally come from a weak bake element or igniter, a drifting temperature sensor or a relay on the control board. We compare a test thermometer against the display and measure each heating part.
GE oven repair in ArvadaGE Wall Oven
Built-in GE and Café wall ovens add tighter cutouts, cooling fans and door locks to the usual oven parts. We test the oven in place whenever possible, checking the lock motor, cooling fan, sensor and elements before any unit comes out of the cabinet.
GE wall oven repair in ArvadaGE Range & Stove
On a GE range, trouble can sit in the cooktop, the oven or the controls that run both. We sort out which section is actually at fault, then test burners, igniters, elements and switches individually.
GE range & stove repair in ArvadaGE Cooktop
Gas cooktops that click without lighting, radiant glass tops with a dead zone and induction surfaces that won't recognize a pan each fail for different reasons. We check spark electrodes and modules, element switches and limiters, or induction generator boards depending on the type you own.
GE cooktop repair in ArvadaGE Microwave
GE microwaves that hum without heating usually have a failed magnetron, diode, capacitor or door switch in the high-voltage circuit. We safely discharge that circuit before testing anything, and on over-the-range units we also check the vent fan and lights.
GE microwave repair in ArvadaGE Range Hood
A GE hood that pulls weakly or won't power on may have greasy filters, a sticking damper, a worn blower motor or a failed switch or control. We test the fan at each speed and check the duct path, since airflow problems often start outside the hood itself.
GE range hood repair in Arvada
Error Codes
GE's Published Error Codes, With Our Notes
The tables below are reproduced from GE Appliances' own support pages for refrigerators, washers, dishwashers and ovens, so each meaning is the manufacturer's wording rather than ours. Codes marked "try it yourself" usually call for a simple step like a reset, a filter cleaning or a door check, while "call a pro" means the fix involves testing or parts inside the machine.
| Code | What it means | Try first | DIY or pro? |
|---|---|---|---|
| FFCall a pro | Freezer temperature is rising too high — check frozen food for thawing.Make sure the freezer door seals and nothing blocks the vents. If the temperature keeps rising, call for service. | Make sure the freezer door seals and nothing blocks the vents. If the temperature keeps rising, call for service. | Call a pro |
| dECall a pro | The defrost system hasn't worked properly in the last 24 hours.Unplug for a minute or two to reset. If dE returns, the defrost system needs a technician. | Unplug for a minute or two to reset. If dE returns, the defrost system needs a technician. | Call a pro |
| CCTry it yourself | The refrigerator temperature is incorrect.Check the temperature controls and set them again. | Check the temperature controls and set them again. | Try it yourself |
| CICall a pro | Check the ice maker for proper operation.Make sure the ice maker is on and the water supply is open. If it still won't work, call for service. | Make sure the ice maker is on and the water supply is open. If it still won't work, call for service. | Call a pro |
| PFTry it yourself | Power to the refrigerator was interrupted.Check food temperatures; the code clears once power is stable. | Check food temperatures; the code clears once power is stable. | Try it yourself |
| DETry it yourself | Demo mode — lights work but cooling is off.Unplug for a minute or two, then plug back in. If DE stays, contact GE with your model number. | Unplug for a minute or two, then plug back in. If DE stays, contact GE with your model number. | Try it yourself |
| tC, tFTry it yourself | Not errors — TurboCool or TurboFreeze is on.Nothing to fix; the code goes away when the feature ends. | Nothing to fix; the code goes away when the feature ends. | Try it yourself |
Source: GE Appliances — refrigerator error, fault or function codes. Codes vary by model — check your owner's manual.
| Code | What it means | Try first | DIY or pro? |
|---|---|---|---|
| dE, E2Try it yourself | The lid was opened, so the washer paused.Close the lid and restart the cycle. | Close the lid and restart the cycle. | Try it yourself |
| PoTry it yourself | The washer has taken too long to drain (2015 and newer top loaders) — there may be a clog.Make sure the drain hose isn't kinked or clogged. | Make sure the drain hose isn't kinked or clogged. | Try it yourself |
Source: GE Appliances — washer FAQ. Codes vary by model — check your owner's manual.
| Code | What it means | Try first | DIY or pro? |
|---|---|---|---|
| C1, FTD, F56Try it yourself | The dishwasher isn't draining (pump-out taking too long).Clean the air gap, check the drain hose and run the disposer. | Clean the air gap, check the drain hose and run the disposer. | Try it yourself |
| C3Call a pro | The dishwasher won't drain.Turn the breaker off for about 30 seconds and reset. If it persists, call for service. | Turn the breaker off for about 30 seconds and reset. If it persists, call for service. | Call a pro |
| C4Try it yourself | Filled twice after a power failure — stuck float switch or clogged drain or sump.Tap the float cover (front left of the tub floor) and clear the sump of debris. | Tap the float cover (front left of the tub floor) and clear the sump of debris. | Try it yourself |
| C6Try it yourself | Incoming water is too cold.GE wants at least 120°F — run the kitchen tap before starting and check the water heater setting. | GE wants at least 120°F — run the kitchen tap before starting and check the water heater setting. | Try it yourself |
| C7Call a pro | The water temperature sensor circuit isn't working.Reset at the breaker for 30 seconds. If it returns, call for service. | Reset at the breaker for 30 seconds. If it returns, call for service. | Call a pro |
| C8Try it yourself | The detergent cup is blocked from opening.Move the item blocking it, close the door and wait 30 seconds. | Move the item blocking it, close the door and wait 30 seconds. | Try it yourself |
| H2OTry it yourself | Low water.Check that the inlet hose isn't kinked. If it only shows on 1-Hour Wash, schedule service. | Check that the inlet hose isn't kinked. If it only shows on 1-Hour Wash, schedule service. | Try it yourself |
| LEAK DETECTED, 999Call a pro | A possible leak was detected.The cycle is cancelled — call for service. | The cycle is cancelled — call for service. | Call a pro |
| PrSCall a pro | The pressure sensor is sending an invalid signal.Most likely a harness or sensor issue — service is recommended. | Most likely a harness or sensor issue — service is recommended. | Call a pro |
Source: GE Appliances — dishwasher error, fault or function codes. Codes vary by model — check your owner's manual.
| Code | What it means | Try first | DIY or pro? |
|---|---|---|---|
| F1Call a pro | A problem with the keypanel — often the keypanel needs replacing.Turning the breaker off for a minute or two may clear it; if not, schedule service. | Turning the breaker off for a minute or two may clear it; if not, schedule service. | Call a pro |
| F2, F20Call a pro | The oven temperature exceeded a preset limit.Turn the breaker off for a minute or two; if the code returns, it needs service. | Turn the breaker off for a minute or two; if the code returns, it needs service. | Call a pro |
| F3Call a pro | The oven temperature sensor needs to be replaced.Needs a technician. | Needs a technician. | Call a pro |
| F9Call a pro | A component in the door lock circuit has failed.Needs a technician. | Needs a technician. | Call a pro |
Source: GE Appliances — range & wall oven error codes. Codes vary by model — check your owner's manual.
Common Problems
Six GE Symptoms Worth a Closer Look
These pairings reflect how GE appliances are generally built, and your technician confirms which cause applies to your unit through testing before naming a part or a price.
Lettuce and milk freezing at the back of the fresh-food section
- Likely causes
- Air damper stuck open, thermistor misreading, temperature set too low, cold air leaking through from the freezer
- What we check
- We watch the damper open and close, check thermistor resistance against its expected range and confirm the board is reading the true temperature.
Dishwasher hums but never fills with water
- Likely causes
- Supply valve under the sink partly closed, failed inlet valve, float switch stuck in the up position, door latch not sensing closed
- What we check
- We confirm water reaches the machine, test the inlet valve coil, free and check the float and verify the latch signal at the control.
Front-load washer smells musty or leaves residue on clothes
- Likely causes
- Water held in the door boot, clogged pump filter, too much or the wrong detergent, a drain that runs slowly
- What we check
- We inspect the boot folds and drain path, clean the pump filter, test drain speed and review detergent and cycle habits with you.
Electric dryer tumbles normally but never warms up
- Likely causes
- Open heating element, blown thermal fuse, failed high-limit thermostat, one side of the power supply missing at the breaker
- What we check
- We check voltage at the terminal block, test the element and each safety device for continuity, and look for a vent restriction that may have tripped them.
Gas burner keeps clicking after it lights, or clicks without lighting
- Likely causes
- Burner cap out of place, moisture or spills on the burner head, cracked electrode, shorted spark switch or worn spark module
- What we check
- We seat and dry the burner parts, inspect the electrode, isolate the switch that is calling for spark and test the module.
Over-the-range microwave fan runs on its own and won't shut off
- Likely causes
- Thermal sensor turning the fan on because the cooktop below is hot, stuck relay on the control board, damaged touchpad
- What we check
- We check whether the cooktop has cooled, test the sensor, then look at the relay and keypad to see which one is holding the fan on.
Arvada Homes
How Arvada Homes Shape a GE Service Call
A few documented facts about Arvada bear directly on how GE appliances here are installed, used and repaired.
Postwar houses with newer GE kitchens
Arvada grew quickly as a Denver suburb after World War II, so many neighborhoods date from the 1950s through the 1970s, and the historic district of Olde Town Arvada is older still. A modern GE in one of these houses often sits in a space planned for a very different appliance, with older outlets, tighter cabinet openings or a gas line routed for an earlier range. We check the supply, the fit and the connections along with the appliance itself, because an installation problem can look exactly like a failed part.
Gas burners from about 5,300 to 5,500 feet
The city sits roughly 5,300 to 5,500 feet above sea level, and thinner air changes how gas mixes and burns in a GE range, oven, cooktop or dryer. Lazy yellow flames, slow preheats or a dryer that takes extra time can come from setup rather than a broken part. Your technician looks at flame quality, ignition timing and heat output before recommending anything.
Getting to you across Jefferson County
Most of the city lies in Jefferson County, with a small part in Adams County, and our drive from Superior reaches neighborhoods along Wadsworth Blvd, Kipling St, CO-72, CO-93 and CO-95. Because the drive to Arvada is so short, we can often fit GE repair visits there into the same day, though we never promise it. Homes near Ralston Creek, Clear Creek and Gold Strike Park are all within the same service area.
Know Your GE
Shop Knowledge That Makes a GE Fix Stick
Four working habits keep a GE diagnosis accurate and help the correct part arrive on the first try.
Find the rating label before anything else
GE puts the model and serial label in a different spot depending on the appliance, and on a refrigerator, dishwasher, oven, washer or dryer it can take a minute of searching. That label tells us exactly which version you own, since two GE units that look identical can use different boards, sensors and wiring. If you can snap a photo of it when you book, we can often research parts before arriving.
Wi-Fi features still run through a control board
Many GE, Profile and Café appliances connect to a phone app and send alerts when something goes wrong. The app is useful, but the main board is still making every decision, so a connected model gets the same hands-on testing as any other. A board that seems faulty may simply be reacting to a bad sensor or a loose harness, and we prove which before suggesting a replacement.
Read a code as a clue, not a verdict
Some GE codes name a specific component, while many others only report that a step took too long or never happened, like water filling slowly or an oven falling short of its target. Those system codes can come from a clogged screen, a kinked hose or low water pressure just as easily as from a part. We treat each code as the starting point for testing.
Genuine parts chosen by model and serial
We install genuine OEM parts matched to your exact unit, so fit, connectors and electrical values follow GE's design. When a part is backordered or no longer made, we tell you plainly what that means for timing and cost. You hear that before agreeing to anything, not after the appliance is apart.
Repair or Replace?
Fixing Your GE Versus Buying New
The lifespan chart from an NAHB study beside this section shows how long each appliance type tends to last, and it is a sensible frame, but it describes averages rather than your particular GE. A newer machine with one failed sensor, igniter, pump or valve is usually worth repairing, since one part costs far less than a replacement and the rest of the appliance has plenty of service left. We weigh the age of the unit, the quote for this repair and what a comparable new model would cost, then lay those numbers side by side for you.
The picture changes when a major component gives out near the end of an appliance's expected life, such as the sealed system on a refrigerator or the tub and bearings on a washer. Energy use matters too, because an older refrigerator or freezer may cost more to run each month than a current model. Parts availability can tip the balance as well, and if a part is discontinued we say so right away. Whatever the numbers show, the decision stays yours, and the diagnostic fee is credited toward the repair if you go ahead.
Typical lifespan by appliance
| Refrigerator | ~13 yrs |
|---|---|
| Freezer | ~11 yrs |
| Washer | ~10 yrs |
| Dryer | ~13 yrs |
| Dishwasher | ~9 yrs |
| Oven | ~13–15 yrs |
| Wall Oven | ~13 yrs |
| Range & Stove | ~13–15 yrs |
| Microwave | ~9 yrs |
Source: NAHB study of home component life. Any brand; real life varies with use and care.
Google Reviews
What GE Owners Say
5.0Every review on Google is five stars.
“We had PointLine Appliance Repair diagnose and repair our 3-year old GE Washing Machine that had ceased to complete the spin dry cycle. Nick was polite and professional. He correctly identified the electronic part that needed to be replaced. He replaced the part and the washing machine now runs like new again. We highly recommend PointLine Dominance Repair!”
Lorin C.October 2026 · Google “I had my GE washing machine repaired and I am so very grateful for your service. It was a far more complicated repair than originally thought, but I cannot stress enough how much I appreciated the openness and honesty. Everything was handled with kindness and tact. I highly recommend this company for all of your appliance repair needs!”
John H.August 2026 · Google “This is a small owner-operated business, which is a big bonus as pricing is much more reasonable than using the chains or PE owned companies. Nick was accommodating, and installed a new evaporator fan in my GE Cafe fridge/freezer quickly and correctly. Highly recommend.”
Aaron F.July 2026 · Google
Membership
PointLine Care Club
One service call is $85. For $99 a year, every service call is free.
- Free service calls all year — no $85 fee
- 1 free maintenance visit a year
- 10% off labor on every repair
$99/ year
One household · renews yearly · cancel anytime before renewal
Property manager or landlord? See our Property Care Club →
Arvada Service Area
GE Repair Across Arvada
ZIP codes 80002, 80003, 80004, 80005, 80007, 80033 and the neighboring communities we serve every week.
Managing rentals? See the Property Care Club.
FAQ
What GE Owners Around Arvada Ask Us
Straight answers for GE owners in Arvada.
Are you GE's own repair service?
No, PointLine is an independent, family-owned company and is not affiliated with GE Appliances. We repair GE, GE Profile and Café appliances using genuine OEM parts, and GE's Monogram line has its own page on our site.
My GE is showing a code. Can I clear it myself?
Sometimes, depending on the code. Check the tables on this page first, and if it's marked "try it yourself," a reset or a quick cleaning may solve it; if the code comes back or is marked "call a pro," stop using the appliance and book a visit.
Do you work on Café and Profile wall ovens and other built-ins?
Yes, we repair built-in GE, Profile and Café wall ovens, cooktops, microwaves and refrigerators. We test them in place whenever possible and handle cabinets and finished surfaces with care if a unit has to come out.
Can you repair a Wi-Fi connected GE that sent an alert to my phone?
Yes. The alert is a helpful clue, but we still test the sensors, wiring and control board on your unit to find the actual fault.
Will you use genuine GE parts, and is the work warrantied?
Yes on both counts. We install genuine OEM parts matched to your model and serial number, and every repair carries a 90-day parts and labor warranty.
How soon can someone come, and what does the visit cost?
Same-day service is often available, though we can't guarantee it. The diagnostic visit is $85, credited toward the repair if you approve the firm quote.
Which ZIP codes do you cover in Arvada?
We serve 80002, 80003, 80004, 80005 and 80007, along with the parts of 80033 the city shares with neighbors. We also work in nearby Wheat Ridge, Westminster, Lakewood, Golden, Thornton and Denver.
Is your GE stalling dinner or laundry?
Call or text (720) 285-3573 or book online, and a technician from our Superior office will find the fault, quote it firmly before any work begins and repair it with genuine OEM parts, with Care Club households covered for $99 a year.
PointLine Appliance Repair is an independent repair company, not affiliated with GE.