Local • Family-Owned
GE Appliance Repair in Denver Metro Area
Thoughtful service for your GE refrigerator, washer, dryer, dishwasher, range and more — including GE Profile and Café.
We repair every GE appliance
- $85 DiagnosticCredited toward your repair
- 90-Day WarrantyParts & labor
- Open 24/7Same-day service often available
- Local & Family-OwnedBased in Superior
GE Repair
Dependable Help for the GE Appliances You Use Every Day
GE appliances show up in kitchens and laundry rooms all over the Denver area, and when one stops working, the whole household feels it. We are a small, family-owned company based in Superior, and we repair GE along with the GE Profile and Café lines in homes across the metro area and Boulder County.
Your technician starts by finding the actual cause, not just the symptom, then gives you a firm quote before any work begins. The $85 diagnostic is credited toward the repair if you go ahead. We use genuine OEM parts and back the work with a 90-day parts and labor warranty, and same-day service is often available.
GE Appliances
GE Appliances We Repair
From the refrigerator to the range hood, these are the GE appliances we work on, including GE Profile and Café models.
GE Refrigerator Repair
GE refrigerators commonly run into warm fresh-food sections, frost buildup from a defrost fault, noisy fans or water on the floor. We repair sealed-system issues, defrost heaters and sensors, fan motors, control boards and water valves.
Refrigerator RepairGE Freezer Repair
A GE freezer that stops holding temperature often has an airflow, defrost or thermostat problem behind it. We diagnose and repair evaporator fans, defrost components, door seals and controls.
Freezer RepairGE Ice Maker Repair
GE ice makers often slow down or stop because of a frozen fill line, a failing water valve or mineral scale. We repair ice maker assemblies, inlet valves, fill tubes and the controls that tell the unit when to make ice.
Ice Maker RepairGE Washer Repair
GE washers commonly have trouble draining, spinning or finishing a cycle, and some stop with a code on the display. We repair drain pumps, lid and door locks, drive components, water valves and control boards.
Washer RepairGE Dryer Repair
A GE dryer that runs but won't heat often has a failed heating element, thermal fuse or gas igniter. We also repair worn drum rollers, belts, idler pulleys and moisture sensors that cut cycles short.
Dryer RepairGE Dishwasher Repair
GE dishwashers frequently leave standing water, fill too little or wash poorly because of clogs, a weak pump or a faulty sensor. We repair drain and wash pumps, inlet valves, float switches, detergent dispensers and leaks.
Dishwasher RepairGE Oven Repair
GE ovens commonly heat unevenly, fail to reach temperature or show an F code tied to a sensor or control. We repair bake and broil elements, igniters, temperature sensors, door locks and control boards.
Oven RepairGE Wall Oven Repair
GE wall ovens share many of the same issues as range ovens, plus cooling fan and door latch problems that come with a built-in fit. We service single and double wall ovens, including convection and combination units.
Wall Oven RepairGE Range & Stove Repair
A GE range may have burners that won't light, a weak flame or an oven that won't hold heat. We repair igniters, spark modules, valves, elements and controls on gas, electric and dual-fuel ranges.
Range & Stove RepairGE Cooktop Repair
GE cooktops often develop clicking igniters, burners that won't stay lit or electric elements that stay cold. We repair gas, radiant and induction cooktops, including switches, elements and control boards.
Cooktop RepairGE Microwave Repair
GE microwaves commonly stop heating, refuse to start or have a dead touchpad or turntable. We repair door switches, high-voltage components, control boards and the vent fans on over-the-range models.
Microwave RepairGE Range Hood Repair
GE range hoods often lose suction, get noisy or have lights and fans that quit. We repair blower motors, switches, lights and controls so smoke and grease leave the kitchen again.
Range Hood Repair
Error Codes
GE Error Codes by Appliance
What common GE codes mean — taken from GE's own support pages — what you can safely try first, and when it's time to call us.
GE Refrigerator Error Codes
Note: codes flash in green on the dispenser panel, usually with a beep.
| Code | What it means | Try first | DIY or pro? |
|---|---|---|---|
| FFCall a pro | Freezer temperature is rising too high — check frozen food for thawing.Make sure the freezer door seals and nothing blocks the vents. If the temperature keeps rising, call for service. | Make sure the freezer door seals and nothing blocks the vents. If the temperature keeps rising, call for service. | Call a pro |
| dECall a pro | The defrost system hasn't worked properly in the last 24 hours.Unplug for a minute or two to reset. If dE returns, the defrost system needs a technician. | Unplug for a minute or two to reset. If dE returns, the defrost system needs a technician. | Call a pro |
| CCTry it yourself | The refrigerator temperature is incorrect.Check the temperature controls and set them again. | Check the temperature controls and set them again. | Try it yourself |
| CICall a pro | Check the ice maker for proper operation.Make sure the ice maker is on and the water supply is open. If it still won't work, call for service. | Make sure the ice maker is on and the water supply is open. If it still won't work, call for service. | Call a pro |
| PFTry it yourself | Power to the refrigerator was interrupted.Check food temperatures; the code clears once power is stable. | Check food temperatures; the code clears once power is stable. | Try it yourself |
| DETry it yourself | Demo mode — lights work but cooling is off.Unplug for a minute or two, then plug back in. If DE stays, contact GE with your model number. | Unplug for a minute or two, then plug back in. If DE stays, contact GE with your model number. | Try it yourself |
| tC, tFTry it yourself | Not errors — TurboCool or TurboFreeze is on.Nothing to fix; the code goes away when the feature ends. | Nothing to fix; the code goes away when the feature ends. | Try it yourself |
Source: GE Appliances — refrigerator error, fault or function codes. Codes vary by model — check your owner's manual.
GE Washer Error Codes
Note: GE publishes only these codes in its general washer FAQ; other GE codes are model-specific — see your owner's manual..
| Code | What it means | Try first | DIY or pro? |
|---|---|---|---|
| dE, E2Try it yourself | The lid was opened, so the washer paused.Close the lid and restart the cycle. | Close the lid and restart the cycle. | Try it yourself |
| PoTry it yourself | The washer has taken too long to drain (2015 and newer top loaders) — there may be a clog.Make sure the drain hose isn't kinked or clogged. | Make sure the drain hose isn't kinked or clogged. | Try it yourself |
Source: GE Appliances — washer FAQ. Codes vary by model — check your owner's manual.
GE Dishwasher Error Codes
| Code | What it means | Try first | DIY or pro? |
|---|---|---|---|
| C1, FTD, F56Try it yourself | The dishwasher isn't draining (pump-out taking too long).Clean the air gap, check the drain hose and run the disposer. | Clean the air gap, check the drain hose and run the disposer. | Try it yourself |
| C3Call a pro | The dishwasher won't drain.Turn the breaker off for about 30 seconds and reset. If it persists, call for service. | Turn the breaker off for about 30 seconds and reset. If it persists, call for service. | Call a pro |
| C4Try it yourself | Filled twice after a power failure — stuck float switch or clogged drain or sump.Tap the float cover (front left of the tub floor) and clear the sump of debris. | Tap the float cover (front left of the tub floor) and clear the sump of debris. | Try it yourself |
| C6Try it yourself | Incoming water is too cold.GE wants at least 120°F — run the kitchen tap before starting and check the water heater setting. | GE wants at least 120°F — run the kitchen tap before starting and check the water heater setting. | Try it yourself |
| C7Call a pro | The water temperature sensor circuit isn't working.Reset at the breaker for 30 seconds. If it returns, call for service. | Reset at the breaker for 30 seconds. If it returns, call for service. | Call a pro |
| C8Try it yourself | The detergent cup is blocked from opening.Move the item blocking it, close the door and wait 30 seconds. | Move the item blocking it, close the door and wait 30 seconds. | Try it yourself |
| H2OTry it yourself | Low water.Check that the inlet hose isn't kinked. If it only shows on 1-Hour Wash, schedule service. | Check that the inlet hose isn't kinked. If it only shows on 1-Hour Wash, schedule service. | Try it yourself |
| LEAK DETECTED, 999Call a pro | A possible leak was detected.The cycle is cancelled — call for service. | The cycle is cancelled — call for service. | Call a pro |
| PrSCall a pro | The pressure sensor is sending an invalid signal.Most likely a harness or sensor issue — service is recommended. | Most likely a harness or sensor issue — service is recommended. | Call a pro |
Source: GE Appliances — dishwasher error, fault or function codes. Codes vary by model — check your owner's manual.
GE Range & Oven Error Codes
| Code | What it means | Try first | DIY or pro? |
|---|---|---|---|
| F1Call a pro | A problem with the keypanel — often the keypanel needs replacing.Turning the breaker off for a minute or two may clear it; if not, schedule service. | Turning the breaker off for a minute or two may clear it; if not, schedule service. | Call a pro |
| F2, F20Call a pro | The oven temperature exceeded a preset limit.Turn the breaker off for a minute or two; if the code returns, it needs service. | Turn the breaker off for a minute or two; if the code returns, it needs service. | Call a pro |
| F3Call a pro | The oven temperature sensor needs to be replaced.Needs a technician. | Needs a technician. | Call a pro |
| F9Call a pro | A component in the door lock circuit has failed.Needs a technician. | Needs a technician. | Call a pro |
Source: GE Appliances — range & wall oven error codes. Codes vary by model — check your owner's manual.
Common Problems
Common GE Problems and What They Usually Mean
These symptoms are typical across GE appliances, and each one points your technician toward a short list of likely causes.
Refrigerator warm but freezer cold
- Likely causes
- A defrost system fault, an iced-over evaporator or a stalled fan; the dE code often points here
- What we check
- Defrost heater, sensor and control, evaporator fan, airflow damper and coil frost
Ice maker stopped making ice
- Likely causes
- A frozen fill tube, a failed water valve, mineral scale or low water pressure; the CI code asks you to check the ice maker
- What we check
- Fill line, inlet valve, ice maker module, water filter and supply pressure
Dishwasher not draining
- Likely causes
- A clogged air gap, kinked hose or blocked disposer connection; C1 and C3 commonly signal a drain problem
- What we check
- Air gap, drain hose, disposer inlet, filter, drain pump and the breaker GE suggests resetting for C3
Dishwasher filling with too little water
- Likely causes
- A partly closed supply valve, a clogged inlet screen or a stuck float; H2O indicates low water
- What we check
- Supply valve, inlet valve and screen, float switch and water pressure
Dryer runs but stays cold
- Likely causes
- A blown thermal fuse, failed heating element or gas igniter, or a clogged vent
- What we check
- Vent airflow, thermal fuses, element or igniter, gas valve coils and thermostats
Oven not heating or showing an F code
- Likely causes
- A failed bake element or igniter, a faulty temperature sensor or a control issue
- What we check
- Element or igniter draw, sensor resistance, wiring and the control board
Before You Call
Finding the Model and Serial Number on a GE
Having the model and serial number ready helps your technician confirm the right parts, and on GE appliances the tag is usually in one of these spots.
Refrigerator
Usually on a label inside the fresh-food section, along a side wall or near the top under the light
Washer
Usually under the lid or on the back of the control panel on top-loaders, and around the door opening on front-loaders
Dryer
Usually inside the door frame or on the edge of the drum opening, sometimes on the back panel
Dishwasher
Usually along the inner edge of the door or on the side of the tub, visible when the door is open
Range or oven
Usually on the frame behind the oven door or drawer, or under the cooktop on some models
Google Reviews
What GE Owners Say
5.0Every review on Google is five stars.
“We had PointLine Appliance Repair diagnose and repair our 3-year old GE Washing Machine that had ceased to complete the spin dry cycle. Nick was polite and professional. He correctly identified the electronic part that needed to be replaced. He replaced the part and the washing machine now runs like new again. We highly recommend PointLine Dominance Repair!”
Lorin C.October 2026 · Google “I had my GE washing machine repaired and I am so very grateful for your service. It was a far more complicated repair than originally thought, but I cannot stress enough how much I appreciated the openness and honesty. Everything was handled with kindness and tact. I highly recommend this company for all of your appliance repair needs!”
John H.August 2026 · Google “This is a small owner-operated business, which is a big bonus as pricing is much more reasonable than using the chains or PE owned companies. Nick was accommodating, and installed a new evaporator fan in my GE Cafe fridge/freezer quickly and correctly. Highly recommend.”
Aaron F.July 2026 · Google
Care Tips
Everyday GE Care for Colorado Homes
Stay ahead of scale
Denver-area water can leave mineral deposits over time, so replace the refrigerator water filter on schedule and run a dishwasher or washer cleaning cycle now and then.
Help the defrost system
In a dry climate, keeping the refrigerator door seals clean and closing doors firmly cuts down on frost and gives the defrost cycle less work.
Keep dryer vents clear
Dry winter air makes lint light and static-prone, so clean the lint screen every load and have the vent line checked for buildup.
Get gas set up for altitude
Homes here sit roughly a mile up, and gas ranges and dryers commonly need the right setup at elevation to burn cleanly and heat as intended.
Membership
PointLine Care Club
One service call is $85. For $99 a year, every service call is free.
- Free service calls all year — no $85 fee
- 1 free maintenance visit a year
- 10% off labor on every repair
$99/ year
One household · renews yearly · cancel anytime before renewal
Property manager or landlord? See our Property Care Club →
Repair or Replace?
Is It Worth Fixing Your GE?
Many GE problems come down to a single part, such as a sensor, pump, igniter or valve, and replacing it is often far simpler and less expensive than buying a new appliance. If the cabinet, drum or sealed system is in good shape, a repair usually makes sense.
Replacement is worth considering when a major component like a compressor or tub has failed on an older unit, or when several problems are stacking up. Your technician will lay out the cost, explain what else may need attention soon and leave the choice to you.
Everyday Brands
Other Popular Brands We Repair
- Whirlpool Repair
- LG Repair
- Samsung Repair
- KitchenAid Repair
- Frigidaire Repair
- Maytag Repair
- Amana Repair
- Kenmore Repair
- Electrolux Repair
- Haier Repair
Service Areas
GE Repair Near You
We repair GE appliances in all 21 communities we serve across the Denver Metro Area and Boulder County.
- GE Repair in Arvada
- GE Repair in Aurora
- GE Repair in Boulder
- GE Repair in Brighton
- GE Repair in Broomfield
- GE Repair in Commerce City
- GE Repair in Denver
- GE Repair in Englewood
- GE Repair in Erie
- GE Repair in Golden
- GE Repair in Highlands Ranch
- GE Repair in Lafayette
- GE Repair in Lakewood
- GE Repair in Littleton
- GE Repair in Longmont
- GE Repair in Louisville
- GE Repair in Northglenn
- GE Repair in Superior
- GE Repair in Thornton
- GE Repair in Westminster
- GE Repair in Wheat Ridge
FAQ
Questions GE Owners Ask
Questions GE owners ask us.
Do you repair GE refrigerators?
Yes, we repair GE refrigerators, including GE Profile and Café models. That covers cooling and defrost problems, ice makers, water dispensers, fans and controls.
What does a service visit cost?
The diagnostic visit is $85, and it is credited toward the repair if you go ahead. You get a firm quote before any work starts, and we accept cash, major credit cards, Venmo, Apple Pay and checks.
Do you use genuine GE parts?
Yes, we install genuine OEM parts. They are made to fit and perform the way your appliance was designed to.
Is the work covered by a warranty?
Yes, every repair comes with a 90-day parts and labor warranty. If the same issue returns within that window, we come back and take care of it.
My GE shows a code like dE, CI or C1. What does that mean?
These codes point to a system that needs attention, such as defrost, the ice maker or draining. Codes vary by model, so check the tables on this page, try simple steps like a reset, and call us if the code returns.
Should I repair my GE or replace it?
In many cases a repair is the more practical choice, especially when one part has failed. If the problem is major or the unit is near the end of its life, your technician will tell you honestly.
Which areas do you serve?
We serve 21 cities across the Denver Metro Area and Boulder County from our office in Superior. Call us to confirm your address and check availability.
Get Your GE Working Again
Call (720) 285-3573 to schedule a visit. Same-day service is often available, and Care Club members save with free service calls, a yearly maintenance visit and 10% off labor for $99 a year.
PointLine Appliance Repair is an independent repair company, not affiliated with GE.