Local • Family-Owned
GE Repair in Broomfield, CO
From a dispenser that won't pour to a dryer that runs cold, your GE gets tested at home by a family company from neighboring Superior.
We repair every GE appliance
- $85 DiagnosticCredited toward your repair
- 90-Day WarrantyParts & labor
- Open 24/7Same-day service often available
- Local & Family-OwnedBased in Superior
GE Repair • Broomfield
Your GE, Diagnosed Before Anything Gets Replaced
Broomfield households who need GE repair can book without waiting on a crew from across the metro, since PointLine sends a technician from our single office at 2600 S Rock Creek Pkwy #103 in Superior, just over the line. We are an independent, family-owned company, not part of GE Appliances, and we work on GE, GE Profile and Café models in the same careful way. The city grew from a small town starting in the 1960s and expanded heavily through the 1990s and 2000s, so a GE here might be a long-serving range in an established kitchen or a connected refrigerator in a much newer house. Both get the same treatment: a test, a firm quote and genuine OEM parts.
A GE that quits rarely tells you which part gave up. A refrigerator running warm could have a frozen coil, a stalled fan or a sensor sending the control board a bad reading, and each of those calls for a different fix at a different price. Swapping parts until the symptom goes away wastes your money and your week. Your technician measures, watches the appliance run and confirms the failed component first, then you see the price and decide whether we go ahead.
GE Appliances
Twelve GE Appliance Types, Kitchen to Laundry
Here is what typically goes wrong on each GE appliance we repair, including GE Profile and Café versions, and where your technician begins.
GE Refrigerator
A GE refrigerator that runs warm, frosts over or clicks without cooling usually points to the defrost system, an evaporator or condenser fan, a temperature sensor or the main control board. We check coil frost patterns, fan operation, sensor readings and compressor behavior before naming a cause.
GE refrigerator repair in BroomfieldGE Freezer
When a GE freezer drifts soft, builds heavy frost or runs without stopping, the usual suspects are a worn door gasket, a failed defrost heater or thermostat, or a fan that has stopped moving air. We test the defrost circuit, inspect the seal and measure how the cabinet holds temperature.
GE freezer repair in BroomfieldGE Ice Maker
An empty bin, hollow cubes or a dispenser that drips often trace back to the water inlet valve, a clogged filter, a frozen fill tube or the ice maker module itself. We follow the water from the supply line to the tray to find where the path breaks.
GE ice maker repair in BroomfieldGE Washer
GE washers that won't drain, stop mid-cycle, leak or shake hard commonly have a blocked pump, a failing lid or door lock, a worn suspension part or a drive problem. We run diagnostic cycles, test the pump and lock circuits, and inspect the hoses and seals.
GE washer repair in BroomfieldGE Dryer
A GE dryer that tumbles without heat, takes forever or shuts off early may have a failed heating element or gas igniter, a tripped thermal fuse or a restricted vent. We test the heat circuit and safety parts and check airflow out of the drum before quoting.
GE dryer repair in BroomfieldGE Dishwasher
Standing water, cloudy dishes or a cycle that stalls on a GE dishwasher often come from a clogged filter, a weak drain or circulation pump, a faulty inlet valve or a heater that no longer warms. We inspect the sump, test the pumps and confirm water fills and drains as it should.
GE dishwasher repair in BroomfieldGE Oven
GE ovens that heat slowly, miss their set temperature or never light usually involve a bake or broil element, a gas igniter, the temperature sensor or a relay on the control board. We measure resistance, watch the heat-up and compare the cavity to the display.
GE oven repair in BroomfieldGE Wall Oven
Built-in GE and Café wall ovens add cooling fans, door locks and tight cabinet fits to the usual heating parts. We check elements, sensors, the self-clean latch and the cooling fan, and protect the surrounding cabinetry if the unit has to come forward.
GE wall oven repair in BroomfieldGE Range & Stove
A GE range can fail on top, in the oven or at the controls, with clicking igniters, weak burners, dead elements or a blank display among the common complaints. We test each section separately so the repair targets the actual fault.
GE range & stove repair in BroomfieldGE Cooktop
Gas GE cooktops tend to show igniter, spark module or burner-port trouble, while electric and induction models more often have a failed element, switch or control board. We check spark, flame and heat output zone by zone.
GE cooktop repair in BroomfieldGE Microwave
A GE microwave that runs without heating, sparks, or has a dead vent fan or light may have a failed magnetron, diode, door switch or fan motor. High-voltage parts stay charged after unplugging, so we discharge and test them safely before any work.
GE microwave repair in BroomfieldGE Range Hood
GE range hoods that go quiet, pull weakly or leave the lights dark usually have a worn fan motor, a bad switch or control, clogged grease filters or a stuck damper. We test the motor and controls and check the path to the outside.
GE range hood repair in Broomfield
Error Codes
Looking Up a GE Code Before You Call
The tables below are taken from GE Appliances' own support pages and cover refrigerators, washers, dishwashers and ovens, so each meaning is in the manufacturer's words. Codes marked try it yourself have a simple step you can safely take, such as a reset or cleaning a filter, while those marked call a pro point to parts, wiring or gas that a technician should handle.
| Code | What it means | Try first | DIY or pro? |
|---|---|---|---|
| FFCall a pro | Freezer temperature is rising too high — check frozen food for thawing.Make sure the freezer door seals and nothing blocks the vents. If the temperature keeps rising, call for service. | Make sure the freezer door seals and nothing blocks the vents. If the temperature keeps rising, call for service. | Call a pro |
| dECall a pro | The defrost system hasn't worked properly in the last 24 hours.Unplug for a minute or two to reset. If dE returns, the defrost system needs a technician. | Unplug for a minute or two to reset. If dE returns, the defrost system needs a technician. | Call a pro |
| CCTry it yourself | The refrigerator temperature is incorrect.Check the temperature controls and set them again. | Check the temperature controls and set them again. | Try it yourself |
| CICall a pro | Check the ice maker for proper operation.Make sure the ice maker is on and the water supply is open. If it still won't work, call for service. | Make sure the ice maker is on and the water supply is open. If it still won't work, call for service. | Call a pro |
| PFTry it yourself | Power to the refrigerator was interrupted.Check food temperatures; the code clears once power is stable. | Check food temperatures; the code clears once power is stable. | Try it yourself |
| DETry it yourself | Demo mode — lights work but cooling is off.Unplug for a minute or two, then plug back in. If DE stays, contact GE with your model number. | Unplug for a minute or two, then plug back in. If DE stays, contact GE with your model number. | Try it yourself |
| tC, tFTry it yourself | Not errors — TurboCool or TurboFreeze is on.Nothing to fix; the code goes away when the feature ends. | Nothing to fix; the code goes away when the feature ends. | Try it yourself |
Source: GE Appliances — refrigerator error, fault or function codes. Codes vary by model — check your owner's manual.
| Code | What it means | Try first | DIY or pro? |
|---|---|---|---|
| dE, E2Try it yourself | The lid was opened, so the washer paused.Close the lid and restart the cycle. | Close the lid and restart the cycle. | Try it yourself |
| PoTry it yourself | The washer has taken too long to drain (2015 and newer top loaders) — there may be a clog.Make sure the drain hose isn't kinked or clogged. | Make sure the drain hose isn't kinked or clogged. | Try it yourself |
Source: GE Appliances — washer FAQ. Codes vary by model — check your owner's manual.
| Code | What it means | Try first | DIY or pro? |
|---|---|---|---|
| C1, FTD, F56Try it yourself | The dishwasher isn't draining (pump-out taking too long).Clean the air gap, check the drain hose and run the disposer. | Clean the air gap, check the drain hose and run the disposer. | Try it yourself |
| C3Call a pro | The dishwasher won't drain.Turn the breaker off for about 30 seconds and reset. If it persists, call for service. | Turn the breaker off for about 30 seconds and reset. If it persists, call for service. | Call a pro |
| C4Try it yourself | Filled twice after a power failure — stuck float switch or clogged drain or sump.Tap the float cover (front left of the tub floor) and clear the sump of debris. | Tap the float cover (front left of the tub floor) and clear the sump of debris. | Try it yourself |
| C6Try it yourself | Incoming water is too cold.GE wants at least 120°F — run the kitchen tap before starting and check the water heater setting. | GE wants at least 120°F — run the kitchen tap before starting and check the water heater setting. | Try it yourself |
| C7Call a pro | The water temperature sensor circuit isn't working.Reset at the breaker for 30 seconds. If it returns, call for service. | Reset at the breaker for 30 seconds. If it returns, call for service. | Call a pro |
| C8Try it yourself | The detergent cup is blocked from opening.Move the item blocking it, close the door and wait 30 seconds. | Move the item blocking it, close the door and wait 30 seconds. | Try it yourself |
| H2OTry it yourself | Low water.Check that the inlet hose isn't kinked. If it only shows on 1-Hour Wash, schedule service. | Check that the inlet hose isn't kinked. If it only shows on 1-Hour Wash, schedule service. | Try it yourself |
| LEAK DETECTED, 999Call a pro | A possible leak was detected.The cycle is cancelled — call for service. | The cycle is cancelled — call for service. | Call a pro |
| PrSCall a pro | The pressure sensor is sending an invalid signal.Most likely a harness or sensor issue — service is recommended. | Most likely a harness or sensor issue — service is recommended. | Call a pro |
Source: GE Appliances — dishwasher error, fault or function codes. Codes vary by model — check your owner's manual.
| Code | What it means | Try first | DIY or pro? |
|---|---|---|---|
| F1Call a pro | A problem with the keypanel — often the keypanel needs replacing.Turning the breaker off for a minute or two may clear it; if not, schedule service. | Turning the breaker off for a minute or two may clear it; if not, schedule service. | Call a pro |
| F2, F20Call a pro | The oven temperature exceeded a preset limit.Turn the breaker off for a minute or two; if the code returns, it needs service. | Turn the breaker off for a minute or two; if the code returns, it needs service. | Call a pro |
| F3Call a pro | The oven temperature sensor needs to be replaced.Needs a technician. | Needs a technician. | Call a pro |
| F9Call a pro | A component in the door lock circuit has failed.Needs a technician. | Needs a technician. | Call a pro |
Source: GE Appliances — range & wall oven error codes. Codes vary by model — check your owner's manual.
Common Problems
Six GE Symptoms and the Usual Suspects
Each row describes how GE appliances are generally built, and testing on your own unit decides which cause applies before any part is ordered or priced.
The fresh-food section runs warm even though the freezer feels fine
- Likely causes
- Defrost heater or sensor failure leaving the coil iced, a stalled evaporator fan, a stuck air damper
- What we check
- Frost pattern on the coil, fan movement, defrost circuit continuity and damper operation
Water dispenser slow or ice production down
- Likely causes
- A clogged water filter, low supply pressure, a failing inlet valve, or a frozen fill tube
- What we check
- Filter condition, water pressure at the valve, valve coil resistance and the fill tube for ice
The washer stops while water is still sitting in the tub
- Likely causes
- Debris in the drain pump, a kinked or clogged drain hose, a failed pump motor, or a lid lock fault
- What we check
- Pump and hose for blockages, pump motor resistance and lock circuit response during a test cycle
Dryer runs but clothes stay damp
- Likely causes
- A failed heating element or gas igniter, an open thermal fuse or cycling thermostat, or a vent restricted by lint
- What we check
- Heat circuit readings, safety part continuity and airflow at the outside vent hood
Oven never reaches the temperature you set
- Likely causes
- Weak bake element or igniter, a temperature sensor reading out of range, a control relay problem
- What we check
- Element or igniter draw, sensor resistance against a known chart and actual cavity temperature during heat-up
Dishwasher leaves film or water behind
- Likely causes
- Clogged filter or spray arms, a weak circulation or drain pump, an inlet valve letting in too little water
- What we check
- Sump and filter, spray arm openings, pump operation and fill volume over a full cycle
Broomfield Homes
Where Local Homes and Water Meet a GE
Three facts about Broomfield bear directly on how GE appliances here are installed, used and repaired.
Established houses beside much newer ones
Broomfield grew from a small town starting in the 1960s, with big surges in the 1990s and 2000s, so the kitchens here vary a lot in age. An older home may hold a GE that has been patched before, while a newer one may have Profile or Café appliances with touch controls and Wi-Fi. Cabinet openings, water line routing and outlet placement vary just as much. Your technician notes the setup around the appliance, because a tight fit or an old supply line can be part of the problem.
Gas burners at roughly 5,300 to 5,400 feet of elevation
Broomfield sits roughly 5,300 to 5,400 feet above sea level, and thinner air changes how gas burns. GE gas ranges, cooktops, wall ovens and dryers depend on correct burner setup to light reliably and burn with a clean, steady flame. A lazy yellow flame, slow ignition or uneven oven heat can come from setup rather than a failed part. We check the flame and the burner before recommending any replacement.
Two water sources supplying ice makers and dishwashers
Broomfield draws treated water from Denver Water and also treats Colorado-Big Thompson and Windy Gap water, managed by Northern Water, at the city's own plant. Whatever reaches your kitchen, a GE refrigerator sends it through a filter, an inlet valve and a fill tube before it becomes ice, and a dishwasher pulls it through its own valve. Changing the filter on schedule and keeping an eye on the supply line protects both. When fills slow down, we trace that path in order rather than guessing at the ice maker.
Know Your GE
Know-How Behind a Lasting GE Fix
These habits guide every GE repair we do for Broomfield owners, whether it's a refrigerator control board or a dryer igniter.
The tag tells us which GE you own
GE prints the model and serial number on a label whose spot changes by appliance, such as inside the refrigerator compartment, near the dishwasher door edge, around the oven frame or at the washer or dryer door opening. Two GE units that look the same can hold different boards, pumps or sensors. Reading the tag first is how we order the right part the first time. Sending a photo of the tag when you book helps us come prepared.
Wi-Fi, touch panels, and the main control board
Many GE, Profile and Café appliances connect to an app and route nearly every action through a control board. A board can look guilty when the real trouble is a sensor feeding it bad data or a loose harness. We test the inputs and outputs around the board before suggesting one, since a board is often among the pricier parts. App alerts are a useful clue, but they are not a full diagnosis.
A code usually points to a process rather than a specific part
Some GE codes point at one component, while others only report that a fill ran long, a drain never finished or the oven missed its target. That tells us which system to examine, not which part to buy. Replacing the obvious suspect without testing can leave the code coming right back. We confirm the cause with a meter and a test cycle first.
Genuine parts, sourced by number
We install genuine OEM parts matched to your model and serial number, so the fit and readings follow the original design. GE parts are generally available through normal supply channels, though timing depends on the specific component. If a part needs to be ordered, we tell you plainly what to expect. Every repair carries our 90-day parts and labor warranty.
Repair or Replace?
Should This GE Get Another Repair?
The lifespan chart next to this section, drawn from an NAHB study, shows how long each appliance type tends to last, and it offers a sensible frame without settling anything on its own. Plenty of GE trouble comes down to a single part such as a fan motor, igniter, pump or sensor, and fixing that one part on an otherwise healthy machine usually makes good sense. With a firm quote in hand, you can compare the true cost of repair against the price of a new unit before deciding. On a built-in Café or Profile appliance, the cabinetry and installation work add to the case for keeping what you have.
Replacement earns a closer look when a major component fails late in an appliance's life, such as the sealed system on an older refrigerator or the tub and bearings on a washer, or when one fault keeps following another. Energy use matters here too, since a refrigerator or freezer runs all day and night and a newer model may draw less electricity. Parts that are no longer made can also tip the balance. If we think a repair is not worth your money, we will say so and leave the choice with you.
Typical lifespan by appliance
| Refrigerator | ~13 yrs |
|---|---|
| Freezer | ~11 yrs |
| Washer | ~10 yrs |
| Dryer | ~13 yrs |
| Dishwasher | ~9 yrs |
| Oven | ~13–15 yrs |
| Wall Oven | ~13 yrs |
| Range & Stove | ~13–15 yrs |
| Microwave | ~9 yrs |
Source: NAHB study of home component life. Any brand; real life varies with use and care.
Google Reviews
What GE Owners Say
5.0Every review on Google is five stars.
“We had PointLine Appliance Repair diagnose and repair our 3-year old GE Washing Machine that had ceased to complete the spin dry cycle. Nick was polite and professional. He correctly identified the electronic part that needed to be replaced. He replaced the part and the washing machine now runs like new again. We highly recommend PointLine Dominance Repair!”
Lorin C.October 2026 · Google “I had my GE washing machine repaired and I am so very grateful for your service. It was a far more complicated repair than originally thought, but I cannot stress enough how much I appreciated the openness and honesty. Everything was handled with kindness and tact. I highly recommend this company for all of your appliance repair needs!”
John H.August 2026 · Google “This is a small owner-operated business, which is a big bonus as pricing is much more reasonable than using the chains or PE owned companies. Nick was accommodating, and installed a new evaporator fan in my GE Cafe fridge/freezer quickly and correctly. Highly recommend.”
Aaron F.July 2026 · Google
Membership
PointLine Care Club
One service call is $85. For $99 a year, every service call is free.
- Free service calls all year — no $85 fee
- 1 free maintenance visit a year
- 10% off labor on every repair
$99/ year
One household · renews yearly · cancel anytime before renewal
Property manager or landlord? See our Property Care Club →
Broomfield Service Area
GE Repair Across Broomfield
ZIP codes 80020, 80023, 80021 and the neighboring communities we serve every week.
Managing rentals? See the Property Care Club.
Other brands in Broomfield
FAQ
GE Questions From Broomfield Homes
Straight answers for GE owners in Broomfield.
Are you part of GE Appliances?
No, PointLine is an independent, family-owned repair company and is not affiliated with GE. We repair GE, GE Profile and Café appliances, and Monogram has its own page on our site.
My GE is displaying an error code. What should I do?
Start by looking it up in the tables on this page. If it says try it yourself, follow that step; if it says call a pro, or if the code keeps coming back, stop using the appliance and book a visit.
Do you work on Café built-ins and Wi-Fi connected GE models?
Yes, we repair built-in and connected GE, Profile and Café appliances. We protect surrounding cabinets and test the controls directly rather than relying only on app alerts.
Will my GE get genuine parts?
Yes, we install genuine OEM parts matched to your model and serial number.
How quickly can a technician come out?
Same-day service is often available since our office is in neighboring Superior, but we can't promise it. Booking early in the day gives you a better shot at a quicker visit.
Which ZIP codes do you cover?
We serve 80020 and 80023 across Broomfield, along with the 80021 areas the city shares with neighbors, plus nearby Louisville, Lafayette, Northglenn, Westminster and Thornton.
What does the visit cost, and does it cover the repair?
The diagnostic visit is $85, credited toward the repair if you approve the firm quote. Every repair carries a 90-day parts and labor warranty, and the PointLine Care Club offers household coverage for $99 a year.
Is a GE holding up your week?
Book online or call or text (720) 285-3573, and a technician from our Superior office will test your GE, give you a firm price and fix it with genuine parts.
PointLine Appliance Repair is an independent repair company, not affiliated with GE.