Local • Family-Owned
Bosch Repair in Broomfield, CO
Independent, family-owned repair for Bosch kitchens and laundry rooms in Broomfield, tested in your home and priced firmly before any work begins.
We repair every Bosch appliance
- $85 DiagnosticCredited toward your repair
- 90-Day WarrantyParts & labor
- Open 24/7Same-day service often available
- Local & Family-OwnedBased in Superior
Bosch Repair • Broomfield
Careful Work for the Bosch You Barely Notice Until It Stops
Looking for Bosch repair in Broomfield from a neighbor you can book directly? PointLine is an independent, family-owned company based in a single office at 2600 S Rock Creek Pkwy #103 in Superior, just next door. We are a small shop, and we handle every call the same way: a full diagnosis at your home, a firm quote you approve before anything is replaced, and genuine OEM parts. Every repair carries a 90-day parts and labor warranty. Same-day visits are often available, though we never promise one.
Bosch appliances in Broomfield kitchens range from a dishwasher that has run through years of school-night loads to a newly installed induction cooktop and wall oven set into fresh cabinetry. Much of the lineup is built in, tightly engineered and run by electronic controls that watch sensors, pumps and heaters. That design keeps the appliance quiet and efficient, but one complaint, such as a cycle that stops or a door that will not unlock, can trace back to several different parts. We test first and order parts second, so you never pay for a guess. That approach is at the center of every visit we make.
Bosch Appliances
The Bosch Machines We Work On, Room by Room
Each Bosch appliance below gets tested where it is installed, so the quote you see is tied to a part we have confirmed.
Bosch Refrigerator
A Bosch refrigerator that runs warm, frosts over or leaks water usually points to airflow, defrost or water-supply trouble rather than a sudden total failure. We check evaporator and condenser fans, the defrost heater and sensor, door seals and the water valve before naming a cause.
Bosch refrigerator repair in BroomfieldBosch Dishwasher
Standing water, poor drying, cloudy glasses and cycles that stall are the usual reasons Bosch dishwasher owners call. We look at the filter and sump, test the drain and circulation pumps, check the heating system and inspect the door seal and leak protection under the tub.
Bosch dishwasher repair in BroomfieldBosch Washer
Bosch front-load washers tend to signal trouble through drain faults, a door that stays locked, heavy shaking on spin or water around the base. We test the drain pump and pressure sensing, check the door lock, inspect suspension parts and bearings, and look closely at the door boot and hoses.
Bosch washer repair in BroomfieldBosch Dryer
A Bosch dryer that runs but leaves clothes damp, shuts off early or makes new noises often has a heating, sensing or airflow problem. We check lint paths and venting or the condenser path, test heating and thermal safety parts, and inspect the drum support and drive.
Bosch dryer repair in BroomfieldBosch Wall Oven
Bosch wall ovens come in for slow preheats, uneven baking, dark displays and door latches that will not release after self-clean. We test bake and broil elements, the temperature sensor, the cooling fan and the latch, then check the control board's outputs before quoting.
Bosch wall oven repair in BroomfieldBosch Range & Stove
Bosch ranges can develop burners that click without lighting, an oven that never reaches its setting or controls that act erratically. We test igniters, spark modules, the oven ignition or elements, sensors and wiring, and on gas models we look at flame quality at each burner.
Bosch range & stove repair in BroomfieldBosch Cooktop
Bosch gas, electric and induction cooktops each fail in their own way, from weak flames to zones that stay cold to touch controls that flash and shut off. We check burner parts and igniters on gas units, elements and switches on radiant glass, and cooling fans, power boards and coils on induction.
Bosch cooktop repair in BroomfieldBosch Range Hood
A Bosch hood that hums without pulling, runs at one speed only or has dark lights usually has a fan motor, switch, control or duct issue. We test the blower and controls, check the damper and ductwork for restrictions, and inspect filters for grease load.
Bosch range hood repair in BroomfieldBosch Microwave
Bosch built-in microwaves and microwave drawers may stop heating, refuse to start or have a drawer that will not open or close smoothly. We safely discharge and test the high-voltage parts, check door switches and the drawer mechanism, and confirm control function before recommending anything.
Bosch microwave repair in Broomfield
Error Codes
What the Bosch Code Tables Can Tell You
The tables below are reproduced from Bosch's own support pages and sorted by appliance, so you can look up the code on your display in the manufacturer's words. When a code is marked as safe to try yourself, the fix is usually something simple, like cleaning a filter or restarting a cycle. Codes marked to call a pro usually mean parts or wiring that a technician needs to test.
| Code | What it means | Try first | DIY or pro? |
|---|---|---|---|
| E22, E-22Try it yourself | Draining problem — a blocked filter, a blocked drain pump or loose pump cover, a kinked drain hose, or a clogged air gap.Wash the filter, clean out the drain pump and make sure its cover clicks shut, straighten the hose and clear the air gap. Then reset the dishwasher. | Wash the filter, clean out the drain pump and make sure its cover clicks shut, straighten the hose and clear the air gap. Then reset the dishwasher. | Try it yourself |
| E24, E25Try it yourself | Drain blocked — drain pump, kinked drain hose or a clogged air gap.Clean the drain pump and filter and check the drain hose and air gap. If it still shows, call for service. | Clean the drain pump and filter and check the drain hose and air gap. If it still shows, call for service. | Try it yourself |
| E23Call a pro | The drain pump is blocked, clogged or faulty.Clear the drain pump. If the pump itself has failed, it needs a technician. | Clear the drain pump. If the pump itself has failed, it needs a technician. | Call a pro |
| E15Call a pro | Water in the base — the leak protection system has activated.Turn off the water to the dishwasher and call for service. | Turn off the water to the dishwasher and call for service. | Call a pro |
| E14, E16, E17, E18, E200Try it yourself | Water isn't flowing into the dishwasher properly (flow meter, fill system or low water).Make sure the water supply is on and the inlet hose isn't kinked or damaged. | Make sure the water supply is on and the inlet hose isn't kinked or damaged. | Try it yourself |
| E12Try it yourself | Limescale has built up in the heat pump.Descale the dishwasher, and use softening salt if your model has a water softener. | Descale the dishwasher, and use softening salt if your model has a water softener. | Try it yourself |
| E09, E21Call a pro | Heat pump heater fault (E09) or the heat pump is blocked (E21).Reset power at the breaker for 30 seconds. If it returns, call for service. | Reset power at the breaker for 30 seconds. If it returns, call for service. | Call a pro |
| E01, E02, E04Call a pro | Control board or heater electronics fault found in the self-test.Reset power at the breaker for 30 seconds. If it returns, call for service. | Reset power at the breaker for 30 seconds. If it returns, call for service. | Call a pro |
| E06Call a pro | Door sensor circuit fault.Reset power for 30 seconds; if it stays, the door sensor needs a technician. | Reset power for 30 seconds; if it stays, the door sensor needs a technician. | Call a pro |
| E07, E10Call a pro | CrystalDry (zeolite) fan motor or chamber heater fault.This needs a technician. | This needs a technician. | Call a pro |
| E19Call a pro | Detergent dispenser solenoid circuit fault.Reset power for 30 seconds; if it returns, call for service. | Reset power for 30 seconds; if it returns, call for service. | Call a pro |
| E27, E9001Try it yourself | The house power supply to the dishwasher is too low.Reset the breaker for 30 seconds. If it happens again, have an electrician check the voltage. | Reset the breaker for 30 seconds. If it happens again, have an electrician check the voltage. | Try it yourself |
| E0100–E0110Call a pro | Electronics miscommunication.Reset power for 30 seconds; if it stays, call for service. | Reset power for 30 seconds; if it stays, call for service. | Call a pro |
| E6160Call a pro | PowerControl lower spray arm can't find its reference position.Reset power; if it returns, call for service. | Reset power; if it returns, call for service. | Call a pro |
| 4 LEDs flashingTry it yourself | A technical issue (models without a code display).Switch off, unplug or turn off the breaker for at least 2 minutes, then restart. If it happens again, call for service. | Switch off, unplug or turn off the breaker for at least 2 minutes, then restart. If it happens again, call for service. | Try it yourself |
Source: Bosch US — dishwasher error codes. Codes vary by model — check your owner's manual.
| Code | What it means | Try first | DIY or pro? |
|---|---|---|---|
| E18, F18Try it yourself | The drain hose is blocked or kinked.Unkink and clean the drain hose and clean the drain pump. | Unkink and clean the drain hose and clean the drain pump. | Try it yourself |
| E17, F17, F29Try it yourself | Inlet filters are blocked or water pressure is too low.With the tap off, clean the filters in the water supply hose and check the water flow. | With the tap off, clean the filters in the water supply hose and check the water flow. | Try it yourself |
| E16, E34, F16, F34Try it yourself | The door isn't locked properly.Close the door until it clicks and check that nothing is caught. | Close the door until it clicks and check that nothing is caught. | Try it yourself |
| E32, F32Try it yourself | Imbalance detected — spin may slow or stop.Wash large and small items together and close zippers and buttons. | Wash large and small items together and close zippers and buttons. | Try it yourself |
| E:00 / -23Call a pro | Water in the base — the appliance is leaking.Turn off the water tap and call for service. | Turn off the water tap and call for service. | Call a pro |
| E80Call a pro | A fault in the drive circuit.Bosch states this can only be fixed by an authorized technician. | Bosch states this can only be fixed by an authorized technician. | Call a pro |
Source: Bosch US — washer error codes. Codes vary by model — check your owner's manual.
| Code | What it means | Try first | DIY or pro? |
|---|---|---|---|
| E02Call a pro | The ice maker is faulty, or the ice and water controls can't communicate.Reset power at the breaker for 30 seconds. If it stays, call for service. | Reset power at the breaker for 30 seconds. If it stays, call for service. | Call a pro |
| E03Call a pro | Dispenser user interface fault.Reset power at the breaker for 30 seconds. If it stays, call for service. | Reset power at the breaker for 30 seconds. If it stays, call for service. | Call a pro |
| E or D + numberTry it yourself | An operational fault.Switch the refrigerator off, unplug it or turn off the breaker, and reconnect after 5 minutes. If the message is back, call for service. | Switch the refrigerator off, unplug it or turn off the breaker, and reconnect after 5 minutes. If the message is back, call for service. | Try it yourself |
Source: Bosch US — refrigeration error codes. Codes vary by model — check your owner's manual.
| Code | What it means | Try first | DIY or pro? |
|---|---|---|---|
| e011Try it yourself | Touch sensor failure on the oven control panel.Clean and dry the panel, then turn the breaker off for 5 minutes and back on. | Clean and dry the panel, then turn the breaker off for 5 minutes and back on. | Try it yourself |
| e005Call a pro | Communication failure between the user interface and the power board.Turn the breaker off for 5 minutes and back on. If it persists, call for service. | Turn the breaker off for 5 minutes and back on. If it persists, call for service. | Call a pro |
| e101Call a pro | The temperature sensor is malfunctioning.Check the power cord wiring, then reset the breaker. If it persists, call for service. | Check the power cord wiring, then reset the breaker. If it persists, call for service. | Call a pro |
| e126Try it yourself | The door lock is malfunctioning.Cancel Self Clean, wait for the door to unlock, and start Self Clean again. | Cancel Self Clean, wait for the door to unlock, and start Self Clean again. | Try it yourself |
Source: Bosch US — freestanding range error codes. Codes vary by model — check your owner's manual.
| Code | What it means | Try first | DIY or pro? |
|---|---|---|---|
| dETry it yourself | Demo mode is on — the zones don't heat.Turn off the breaker for 30 seconds, then touch any control within 3 minutes. | Turn off the breaker for 30 seconds, then touch any control within 3 minutes. | Try it yourself |
| F2, F4Try it yourself | The electronics overheated and one zone (F2) or all zones (F4) switched off.Let the cooktop cool, then touch any control and keep cooking. | Let the cooktop cool, then touch any control and keep cooking. | Try it yourself |
| F1, F6 (induction)Try it yourself | A cooking zone overheated and switched off to protect the surface.Let it cool, then switch the zone back on. | Let it cool, then switch the zone back on. | Try it yourself |
| F5Try it yourself | Hot cookware is too close to the control panel.Move the pan off the controls, wait a few seconds and touch any control. | Move the pan off the controls, wait a few seconds and touch any control. | Try it yourself |
| F8Try it yourself | A zone ran a long time without any input, so the automatic time limit turned it off.Touch any control and set the zone again. | Touch any control and set the zone again. | Try it yourself |
| U400, E9000, E9010, E9011Call a pro | Supply voltage is outside the normal range, or the cooktop isn't connected correctly.Have the connection and voltage checked — call your utility or an electrician, or call us. | Have the connection and voltage checked — call your utility or an electrician, or call us. | Call a pro |
| D or E + numberCall a pro | An operational fault.Switch the cooktop off and on. If the message comes back, call for service with the exact code. | Switch the cooktop off and on. If the message comes back, call for service with the exact code. | Call a pro |
| All indicators flashingTry it yourself | The control panel is wet or something is covering it.Dry the panel or remove the object. | Dry the panel or remove the object. | Try it yourself |
Source: Bosch US — cooktop and rangetop error codes. Codes vary by model — check your owner's manual.
| Code | What it means | Try first | DIY or pro? |
|---|---|---|---|
| E11Try it yourself | The touch keys aren't working properly — often condensation on the keypad.Dry the control panel, then switch the breaker off for 10 seconds and back on. | Dry the control panel, then switch the breaker off for 10 seconds and back on. | Try it yourself |
| E + numberCall a pro | A malfunction (the control may beep).Press any button to stop the beeping and note the code. If it keeps coming back, switch off the breaker and call for service. | Press any button to stop the beeping and note the code. If it keeps coming back, switch off the breaker and call for service. | Call a pro |
Source: Bosch US — oven and microwave error codes. Codes vary by model — check your owner's manual.
Common Problems
Six Bosch Symptoms and the Suspects Behind Them
These pairings come from how Bosch appliances are generally designed, and your technician confirms which cause applies to your unit before you see a price.
Dishwasher leaves water in the bottom
- Likely causes
- Clogged filter or sump, blocked drain hose or air gap, failed drain pump, garbage disposal knockout not removed on a new install
- What we check
- Filter and sump condition, drain hose routing and kinks, pump operation and current draw, disposal connection
Dishes come out wet or spotted
- Likely causes
- Low rinse aid, a heating system fault, a blocked spray arm, overloaded racks, water entering too cool
- What we check
- Rinse aid dispenser, heater and sensor readings, spray arm openings, inlet water temperature, loading pattern
Refrigerator warm while freezer seems fine
- Likely causes
- Frost-blocked evaporator from a defrost fault, stalled evaporator fan, damper stuck closed, worn door gasket
- What we check
- Frost pattern on the coil, fan operation, defrost heater and sensor continuity, damper movement, gasket seal
Front-load washer won't drain or spin
- Likely causes
- Debris in the pump filter, failed drain pump, door lock not confirming, unbalanced load, pressure sensing fault
- What we check
- Pump filter, pump function, lock signal to the control, load balance, pressure readings during the cycle
Oven heats slowly or runs off temperature
- Likely causes
- Weak or open bake element, failing gas igniter, drifting temperature sensor, door gasket gaps, cooling fan trouble
- What we check
- Element resistance, igniter draw, sensor values against actual temperature, gasket condition, fan operation
Induction zone won't heat or shuts off
- Likely causes
- Incompatible or warped cookware, overheating from a blocked cooling path, failed power board, coil fault, control panel error
- What we check
- Pan detection with a magnetic pan, fan and air path under the glass, power board outputs, coil continuity, touch control response
Broomfield Homes
How Broomfield Homes Shape Bosch Service
A few simple facts about the city help explain how Bosch appliances here are installed, used and repaired.
Established houses and much newer builds
Broomfield began as a small town in the 1960s and saw its biggest growth in the 1990s and 2000s, so kitchens here range from older houses to much newer homes. In established houses, a built-in Bosch dishwasher or wall oven is often fitted into a cabinet opening first sized for something else, which affects how it slides out and goes back in. In newer homes the appliances may be recent, with more electronics and app features to read through. Either way, we check how the unit was installed before we pull it.
Gas cooking at about 5,300 to 5,400 feet
Broomfield sits at roughly 5,300 to 5,400 feet, and the thinner air at that height changes how gas burns. A Bosch gas range or cooktop needs the burners set up correctly to give a clean, steady flame, so yellow tips, flames that lift off the burner or soot on your pans deserve a look. When we work on gas burners, we check flame quality as part of the visit rather than stopping at the igniter.
Two water supplies feeding your appliances
Broomfield's water comes from two sources: treated water purchased from Denver Water, plus Colorado-Big Thompson and Windy Gap water managed by Northern Water and treated at the city's own plant. That supply reaches a Bosch dishwasher, washer or refrigerator ice maker through a shutoff valve, a supply line and an inlet valve, each of which can wear or partly clog. Slow fills, low ice production and drips at the base often start somewhere along that path, so we follow the water from the wall to the appliance before replacing anything inside.
Premium Appliance Care
How We Handle Built-In Bosch Work
A premium built-in shares space with finished woodwork, stone and plumbing, so how we treat the kitchen matters as much as the part we install.
Floors, panels and counters come first
Before a panel-ready dishwasher leaves its opening or a wall oven comes forward, we lay floor protection and cover nearby cabinet faces and stone edges. Custom panels are removed and stored carefully, and mounting screws are tracked so the fit and reveal match when the unit goes back.
Airflow that built-ins depend on
Built-in refrigerators move heat through a front grille or toe-kick opening, and wall ovens and induction cooktops use fans to keep electronics cool. We check that those paths are clear and that the appliance was installed with the clearances its design expects, since a blocked opening can cause repeat failures no new part will cure.
Genuine parts, installed by the book
We order genuine OEM parts by your model and serial number, because Bosch units that look the same can use different boards, pumps or sensors. Installation follows proper procedure, from reconnecting water and gas lines to running a full test cycle before we leave.
Why a rushed fix costs more
On a luxury built-in, a wrong guess can mean paying for a part you did not need, a chipped countertop, a bent panel or a water line pinched behind the cabinet. Slow, methodical testing protects your money and your kitchen, and it is the reason our quote comes after diagnosis, not before.
From Our Own Jobs
Real Bosch Repairs From Our Own Jobs
Real photos from our own service calls around the Denver Metro Area — not stock images.
Bosch dishwasher showing an E:15 code 
Bosch dishwasher showing an E:23 code
Repair or Replace?
Keeping a Bosch Versus Starting Over
The lifespan chart beside this section, drawn from an NAHB study, gives a rough picture of how long each appliance type tends to serve, and it is a sensible place to begin. Your own appliance's condition matters more than its age on paper, so we look at the cabinet, tub, seals and controls alongside the failed part. Replacement deserves serious thought when a repair would cost a large share of a new unit, when a refrigerator's sealed system fails late in its life, when rust has reached a tub or frame, or when several major parts are wearing out at once. If we think your money would be better spent on something new, we will say so plainly.
Built-in Bosch appliances often tilt the math toward repair. Swapping one out can mean finding a model with matching dimensions, reworking an opening, refitting custom panels and paying for installation on top of the purchase. A single failed pump, element or board, fixed with a genuine part and backed by our 90-day warranty, frequently keeps the kitchen intact for far less disruption. Broomfield owners who need Bosch repair can weigh the practical side of the decision once they have a firm quote in hand.
Typical lifespan by appliance
| Refrigerator | ~13 yrs |
|---|---|
| Dishwasher | ~9 yrs |
| Washer | ~10 yrs |
| Dryer | ~13 yrs |
| Wall Oven | ~13 yrs |
| Range & Stove | ~13–15 yrs |
| Microwave | ~9 yrs |
Source: NAHB study of home component life. Any brand; real life varies with use and care.
Google Reviews
What Our Customers Say
5.0Every review on Google is five stars.
“Had an issue with an ice maker in our freezer, Nick solved it instantly. Timely, great communication! I would recommend Nick to anyone.”
Oscar O.July 2026 · Google “Nick is professional, highly-skilled, and did a great job troubleshooting and fixing our refrigerator. Our Whirlpool refrigerator was dispensing water randomly. Nick figured out the root cause, ordered a part, and then fixed it the day the part arrived. With such a potentially deleterious issue, Nick took care of it quickly, and effectively. We are grateful. I will certainly call upon his expertise again.”
Brian R.August 2026 · Google “Our technician was prompt, friendly, knowledgeable, respectful and kind! Fixed our busted GE double wall ovens in a couple hours! Inspection, part, labor and 90 day warranty are included in the price we paid!”
Koya M.July 2026 · Google
Membership
PointLine Care Club
One service call is $85. For $99 a year, every service call is free.
- Free service calls all year — no $85 fee
- 1 free maintenance visit a year
- 10% off labor on every repair
$99/ year
One household · renews yearly · cancel anytime before renewal
Property manager or landlord? See our Property Care Club →
Broomfield Service Area
Bosch Repair Across Broomfield
ZIP codes 80020, 80023, 80021 and the neighboring communities we serve every week.
Managing rentals? See the Property Care Club.
Other brands in Broomfield
FAQ
Bosch Questions From Broomfield Households
Straight answers for Bosch owners in Broomfield.
Is PointLine part of Bosch?
No. We are an independent, family-owned repair company and have no affiliation with Bosch. We fix Bosch appliances with genuine OEM parts, and the pricing and warranty are our own.
My Bosch is showing an error code. Should I keep using it?
Start by looking up the code in the tables on this page. If it is marked as something you can try yourself, a simple step may clear it; if it calls for a technician, or the appliance is leaking, sparking or smelling hot, stop using it and book a visit.
Can you work on panel-ready dishwashers and built-in wall ovens?
Yes, we repair built-in and panel-ready Bosch appliances too. We protect the surrounding cabinetry and stone, remove panels carefully and reinstall the unit to its original fit.
The Bosch app sent an alert. Is that enough to diagnose it?
An app alert is a helpful clue, but not a diagnosis. It tells us which system noticed a problem, and testing at your home confirms which part actually failed.
Will you use genuine Bosch parts?
Yes, the parts we install are genuine OEM parts matched to your model and serial number. Having that label information ready when you book helps us plan the visit.
How quickly can a technician get to you?
Same-day service is often available from our office in neighboring Superior, but we can't guarantee it on any given day. Booking early in the day gives a better chance of a quick visit.
Which Broomfield ZIP codes do you cover?
We serve 80020 and 80023, plus the shared 80021. We also serve nearby Louisville, Superior, Lafayette, Northglenn, Westminster and Thornton.
Which Bosch in your home needs attention?
Book online or call or text (720) 285-3573 for a $85 diagnostic credited toward the repair, and ask about the PointLine Care Club at $99 a year for ongoing household coverage.
PointLine Appliance Repair is an independent repair company, not affiliated with Bosch.