Local • Family-Owned
Bosch Appliance Repair in Denver Metro Area
Thoughtful service for your Bosch dishwasher, refrigerator, oven, cooktop and laundry.
We repair every Bosch appliance
- $85 DiagnosticCredited toward your repair
- 90-Day WarrantyParts & labor
- Open 24/7Same-day service often available
- Local & Family-OwnedBased in Superior
Bosch Repair
Bosch Repair That Respects How Your Kitchen Works
Bosch appliances are known for quiet operation, clean lines and tight built-in fits, and the dishwasher in particular tends to become part of the daily rhythm of a home. When one stops draining, heating or starting, you want someone who takes the time to understand the problem and treats your cabinetry and floors with care. PointLine is a small, family-owned company based in Superior, and we serve 21 cities across the Denver Metro Area and Boulder County.
Each visit begins with a thorough diagnosis so your technician can pinpoint the real cause rather than guess. You get a firm quote before anything is replaced, and the $85 diagnostic fee is credited toward the repair if you go ahead. We use genuine OEM parts, back our work with a 90-day parts and labor warranty, and same-day appointments are often available depending on the schedule.
Bosch Appliances
Bosch Appliances on Our Repair List
From the dishwasher to the range hood, here is what we work on and the issues each type commonly runs into.
Bosch Refrigerator Repair
Bosch refrigerators commonly develop warm compartments, frost buildup, noisy fans or ice makers that slow down or stop. We repair sealed-system symptoms, defrost components, fans, controls, water valves and ice and water dispensers.
Refrigerator RepairBosch Dishwasher Repair
Bosch dishwashers are often the heart of the kitchen, and the usual troubles are poor draining, water in the base, dishes that stay wet and units that will not start. We clean and replace drain pumps, address leaks and the leak-protection float, repair heating and drying issues, and diagnose control boards and door latches.
Dishwasher RepairBosch Washer Repair
Bosch front-load washers can stop draining or spinning, leave water in the drum or show door lock and water supply errors. We service drain pumps and filters, door locks, inlet valves, motors, bearings and electronic controls.
Washer RepairBosch Dryer Repair
Bosch dryers commonly run without heat, take too long to dry or stop mid-cycle, and condensation models can struggle when the condenser or water container needs attention. We repair heating components, sensors, belts, drums, door switches and controls.
Dryer RepairBosch Wall Oven Repair
Bosch wall ovens may heat unevenly, fail to reach temperature or show touch-key and display problems. We repair bake and broil elements, temperature sensors, convection fans, door locks and control panels.
Wall Oven RepairBosch Range & Stove Repair
Bosch ranges can develop weak or uneven burners, ovens that will not heat and igniters that click without lighting. We service gas and electric ranges, including burners, igniters, elements, sensors and controls, with gas units set up correctly for Colorado altitude.
Range & Stove RepairBosch Cooktop Repair
Bosch induction and electric cooktops sometimes show error codes, refuse to recognize cookware or have zones that stop heating. We diagnose induction generators, sensors, touch controls and power supply issues, and we also work on gas cooktops.
Cooktop RepairBosch Range Hood Repair
Bosch range hoods commonly lose fan speed, get noisy or have lights and controls that quit working. We repair blower motors, switches, control boards and lighting.
Range Hood RepairBosch Microwave Repair
Bosch built-in and drawer microwaves can stop heating, have drawers or doors that will not open smoothly or show touch-key errors. We repair door and drawer mechanisms, magnetrons, fuses, sensors and control panels.
Microwave Repair
Error Codes
Bosch Error Codes by Appliance
What common Bosch codes mean — taken from Bosch's own support pages — what you can safely try first, and when it's time to call us.
Bosch Dishwasher Error Codes
| Code | What it means | Try first | DIY or pro? |
|---|---|---|---|
| E22, E-22Try it yourself | Draining problem — a blocked filter, a blocked drain pump or loose pump cover, a kinked drain hose, or a clogged air gap.Wash the filter, clean out the drain pump and make sure its cover clicks shut, straighten the hose and clear the air gap. Then reset the dishwasher. | Wash the filter, clean out the drain pump and make sure its cover clicks shut, straighten the hose and clear the air gap. Then reset the dishwasher. | Try it yourself |
| E24, E25Try it yourself | Drain blocked — drain pump, kinked drain hose or a clogged air gap.Clean the drain pump and filter and check the drain hose and air gap. If it still shows, call for service. | Clean the drain pump and filter and check the drain hose and air gap. If it still shows, call for service. | Try it yourself |
| E23Call a pro | The drain pump is blocked, clogged or faulty.Clear the drain pump. If the pump itself has failed, it needs a technician. | Clear the drain pump. If the pump itself has failed, it needs a technician. | Call a pro |
| E15Call a pro | Water in the base — the leak protection system has activated.Turn off the water to the dishwasher and call for service. | Turn off the water to the dishwasher and call for service. | Call a pro |
| E14, E16, E17, E18, E200Try it yourself | Water isn't flowing into the dishwasher properly (flow meter, fill system or low water).Make sure the water supply is on and the inlet hose isn't kinked or damaged. | Make sure the water supply is on and the inlet hose isn't kinked or damaged. | Try it yourself |
| E12Try it yourself | Limescale has built up in the heat pump.Descale the dishwasher, and use softening salt if your model has a water softener. | Descale the dishwasher, and use softening salt if your model has a water softener. | Try it yourself |
| E09, E21Call a pro | Heat pump heater fault (E09) or the heat pump is blocked (E21).Reset power at the breaker for 30 seconds. If it returns, call for service. | Reset power at the breaker for 30 seconds. If it returns, call for service. | Call a pro |
| E01, E02, E04Call a pro | Control board or heater electronics fault found in the self-test.Reset power at the breaker for 30 seconds. If it returns, call for service. | Reset power at the breaker for 30 seconds. If it returns, call for service. | Call a pro |
| E06Call a pro | Door sensor circuit fault.Reset power for 30 seconds; if it stays, the door sensor needs a technician. | Reset power for 30 seconds; if it stays, the door sensor needs a technician. | Call a pro |
| E07, E10Call a pro | CrystalDry (zeolite) fan motor or chamber heater fault.This needs a technician. | This needs a technician. | Call a pro |
| E19Call a pro | Detergent dispenser solenoid circuit fault.Reset power for 30 seconds; if it returns, call for service. | Reset power for 30 seconds; if it returns, call for service. | Call a pro |
| E27, E9001Try it yourself | The house power supply to the dishwasher is too low.Reset the breaker for 30 seconds. If it happens again, have an electrician check the voltage. | Reset the breaker for 30 seconds. If it happens again, have an electrician check the voltage. | Try it yourself |
| E0100–E0110Call a pro | Electronics miscommunication.Reset power for 30 seconds; if it stays, call for service. | Reset power for 30 seconds; if it stays, call for service. | Call a pro |
| E6160Call a pro | PowerControl lower spray arm can't find its reference position.Reset power; if it returns, call for service. | Reset power; if it returns, call for service. | Call a pro |
| 4 LEDs flashingTry it yourself | A technical issue (models without a code display).Switch off, unplug or turn off the breaker for at least 2 minutes, then restart. If it happens again, call for service. | Switch off, unplug or turn off the breaker for at least 2 minutes, then restart. If it happens again, call for service. | Try it yourself |
Source: Bosch US — dishwasher error codes. Codes vary by model — check your owner's manual.
Bosch Washer Error Codes
| Code | What it means | Try first | DIY or pro? |
|---|---|---|---|
| E18, F18Try it yourself | The drain hose is blocked or kinked.Unkink and clean the drain hose and clean the drain pump. | Unkink and clean the drain hose and clean the drain pump. | Try it yourself |
| E17, F17, F29Try it yourself | Inlet filters are blocked or water pressure is too low.With the tap off, clean the filters in the water supply hose and check the water flow. | With the tap off, clean the filters in the water supply hose and check the water flow. | Try it yourself |
| E16, E34, F16, F34Try it yourself | The door isn't locked properly.Close the door until it clicks and check that nothing is caught. | Close the door until it clicks and check that nothing is caught. | Try it yourself |
| E32, F32Try it yourself | Imbalance detected — spin may slow or stop.Wash large and small items together and close zippers and buttons. | Wash large and small items together and close zippers and buttons. | Try it yourself |
| E:00 / -23Call a pro | Water in the base — the appliance is leaking.Turn off the water tap and call for service. | Turn off the water tap and call for service. | Call a pro |
| E80Call a pro | A fault in the drive circuit.Bosch states this can only be fixed by an authorized technician. | Bosch states this can only be fixed by an authorized technician. | Call a pro |
Source: Bosch US — washer error codes. Codes vary by model — check your owner's manual.
Bosch Refrigerator Error Codes
| Code | What it means | Try first | DIY or pro? |
|---|---|---|---|
| E02Call a pro | The ice maker is faulty, or the ice and water controls can't communicate.Reset power at the breaker for 30 seconds. If it stays, call for service. | Reset power at the breaker for 30 seconds. If it stays, call for service. | Call a pro |
| E03Call a pro | Dispenser user interface fault.Reset power at the breaker for 30 seconds. If it stays, call for service. | Reset power at the breaker for 30 seconds. If it stays, call for service. | Call a pro |
| E or D + numberTry it yourself | An operational fault.Switch the refrigerator off, unplug it or turn off the breaker, and reconnect after 5 minutes. If the message is back, call for service. | Switch the refrigerator off, unplug it or turn off the breaker, and reconnect after 5 minutes. If the message is back, call for service. | Try it yourself |
Source: Bosch US — refrigeration error codes. Codes vary by model — check your owner's manual.
Bosch Range Error Codes
| Code | What it means | Try first | DIY or pro? |
|---|---|---|---|
| e011Try it yourself | Touch sensor failure on the oven control panel.Clean and dry the panel, then turn the breaker off for 5 minutes and back on. | Clean and dry the panel, then turn the breaker off for 5 minutes and back on. | Try it yourself |
| e005Call a pro | Communication failure between the user interface and the power board.Turn the breaker off for 5 minutes and back on. If it persists, call for service. | Turn the breaker off for 5 minutes and back on. If it persists, call for service. | Call a pro |
| e101Call a pro | The temperature sensor is malfunctioning.Check the power cord wiring, then reset the breaker. If it persists, call for service. | Check the power cord wiring, then reset the breaker. If it persists, call for service. | Call a pro |
| e126Try it yourself | The door lock is malfunctioning.Cancel Self Clean, wait for the door to unlock, and start Self Clean again. | Cancel Self Clean, wait for the door to unlock, and start Self Clean again. | Try it yourself |
Source: Bosch US — freestanding range error codes. Codes vary by model — check your owner's manual.
Bosch Cooktop Error Codes
| Code | What it means | Try first | DIY or pro? |
|---|---|---|---|
| dETry it yourself | Demo mode is on — the zones don't heat.Turn off the breaker for 30 seconds, then touch any control within 3 minutes. | Turn off the breaker for 30 seconds, then touch any control within 3 minutes. | Try it yourself |
| F2, F4Try it yourself | The electronics overheated and one zone (F2) or all zones (F4) switched off.Let the cooktop cool, then touch any control and keep cooking. | Let the cooktop cool, then touch any control and keep cooking. | Try it yourself |
| F1, F6 (induction)Try it yourself | A cooking zone overheated and switched off to protect the surface.Let it cool, then switch the zone back on. | Let it cool, then switch the zone back on. | Try it yourself |
| F5Try it yourself | Hot cookware is too close to the control panel.Move the pan off the controls, wait a few seconds and touch any control. | Move the pan off the controls, wait a few seconds and touch any control. | Try it yourself |
| F8Try it yourself | A zone ran a long time without any input, so the automatic time limit turned it off.Touch any control and set the zone again. | Touch any control and set the zone again. | Try it yourself |
| U400, E9000, E9010, E9011Call a pro | Supply voltage is outside the normal range, or the cooktop isn't connected correctly.Have the connection and voltage checked — call your utility or an electrician, or call us. | Have the connection and voltage checked — call your utility or an electrician, or call us. | Call a pro |
| D or E + numberCall a pro | An operational fault.Switch the cooktop off and on. If the message comes back, call for service with the exact code. | Switch the cooktop off and on. If the message comes back, call for service with the exact code. | Call a pro |
| All indicators flashingTry it yourself | The control panel is wet or something is covering it.Dry the panel or remove the object. | Dry the panel or remove the object. | Try it yourself |
Source: Bosch US — cooktop and rangetop error codes. Codes vary by model — check your owner's manual.
Bosch Wall Oven & Microwave Error Codes
| Code | What it means | Try first | DIY or pro? |
|---|---|---|---|
| E11Try it yourself | The touch keys aren't working properly — often condensation on the keypad.Dry the control panel, then switch the breaker off for 10 seconds and back on. | Dry the control panel, then switch the breaker off for 10 seconds and back on. | Try it yourself |
| E + numberCall a pro | A malfunction (the control may beep).Press any button to stop the beeping and note the code. If it keeps coming back, switch off the breaker and call for service. | Press any button to stop the beeping and note the code. If it keeps coming back, switch off the breaker and call for service. | Call a pro |
Source: Bosch US — oven and microwave error codes. Codes vary by model — check your owner's manual.
Common Problems
Bosch Issues Worth Calling About
These problems are common for Bosch appliances, and most of them come down to a handful of likely causes.
Dishwasher not draining (E22, E24, E25)
- Likely causes
- A clogged filter, debris in the drain pump, a kinked drain hose or a blocked air gap or disposal connection
- What we check
- Filter and pump condition, drain hose routing, air gap and disposal knockout, pump operation
Water in the base or E15 on the dishwasher
- Likely causes
- A leak from a hose, seal, pump or tub has tripped the leak-protection float
- What we check
- Source of the leak, hoses and seals, pump housing, float switch and the base tray
Dishes wet or not getting hot
- Likely causes
- Rinse aid empty, a failed heater or heat pump, temperature sensor issues, or limescale (E12)
- What we check
- Heating components, sensors, rinse aid dispenser, scale buildup and cycle settings
Dishwasher won't start or all lights flash
- Likely causes
- A door latch fault, control electronics, low house voltage (E27) or a glitch that needs a full power reset
- What we check
- Door latch and switch, power supply, control board and the codes stored in memory
Washer not draining or not spinning
- Likely causes
- A full pump filter, a blocked drain hose, an unbalanced load or a door lock or motor fault
- What we check
- Pump filter and hose, door lock, motor and drive, suspension and error history
Refrigerator not cooling or ice maker stopped
- Likely causes
- Dirty condenser coils, a failed fan, defrost problems, a frozen fill tube or a faulty water valve
- What we check
- Airflow and coils, fans, defrost system, water supply and valve, ice maker and controls
Before You Call
Where to Find the Bosch Rating Label
Having the model and serial number ready helps your technician bring the right parts, and the label is usually easy to spot once you know where to look.
Dishwasher
Usually on the top or side edge of the inner door, visible when you open the door
Refrigerator
Usually inside the fresh-food compartment on a side wall or near the top, or behind the lower grille on built-in units
Washer
Usually on the inside rim of the door opening or behind the small filter access panel at the bottom front
Dryer
Usually inside the door opening on the frame or on the back of the door
Wall Oven or Range
Usually on the oven frame when the door is open, or behind the storage drawer on a range
Care Tips
Bosch Care Habits for Colorado Homes
Clean the dishwasher filter often
Bosch dishwashers use a manual filter at the bottom of the tub, so twist it out every few weeks, rinse it under warm water with a soft brush and lock it back in place. A clean filter is one of the simplest ways to prevent drain errors and gritty dishes.
Stay ahead of mineral scale
Denver-area water ranges from soft to moderately hard, and scale commonly builds up in dishwashers, washers and ice makers. Keep rinse aid filled, run a dishwasher cleaner or descaler periodically, and change refrigerator water filters on schedule.
Give the washer room to breathe
Front-load washers commonly hold moisture in the door gasket, so wipe it dry and leave the door cracked between loads. Clean the drain pump filter now and then to keep draining and spinning reliable.
Mind gas setup and dry air
At 5,000 feet and up, gas ranges and cooktops need correct setup to burn cleanly, so yellow or uneven flames are worth a look. Dry winters also mean dryer lint and dust gather fast, so clean the lint filter every load and keep refrigerator coils clear.
Membership
PointLine Care Club
One service call is $85. For $99 a year, every service call is free.
- Free service calls all year — no $85 fee
- 1 free maintenance visit a year
- 10% off labor on every repair
$99/ year
One household · renews yearly · cancel anytime before renewal
Property manager or landlord? See our Property Care Club →
Repair or Replace?
Fix It or Replace It: Thinking Through a Bosch Repair
Many Bosch appliances are built into the cabinetry, and replacing one can mean matching dimensions, trim and panels, not just buying a new unit. When the frame, tub and sealed system are in good shape, a repair to a pump, heater, sensor or control board is often the more practical choice and keeps your kitchen looking the way it was designed.
Replacement can make more sense when the needed repair approaches the cost of a new appliance, when several major components are failing at once or when the unit is quite old and parts are hard to justify. Your technician will explain what we find, give you a firm quote and share an honest opinion, so the decision stays entirely yours.
Premium & Luxury Brands
Other Premium Brands We Repair
- Sub-Zero Repair
- Wolf Repair
- Thermador Repair
- Miele Repair
- Viking Repair
- JennAir Repair
- Dacor Repair
- Monogram Repair
- ASKO Repair
Service Areas
Bosch Repair Near You
We repair Bosch appliances in all 21 communities we serve across the Denver Metro Area and Boulder County.
- Bosch Repair in Arvada
- Bosch Repair in Aurora
- Bosch Repair in Boulder
- Bosch Repair in Brighton
- Bosch Repair in Broomfield
- Bosch Repair in Commerce City
- Bosch Repair in Denver
- Bosch Repair in Englewood
- Bosch Repair in Erie
- Bosch Repair in Golden
- Bosch Repair in Highlands Ranch
- Bosch Repair in Lafayette
- Bosch Repair in Lakewood
- Bosch Repair in Littleton
- Bosch Repair in Longmont
- Bosch Repair in Louisville
- Bosch Repair in Northglenn
- Bosch Repair in Superior
- Bosch Repair in Thornton
- Bosch Repair in Westminster
- Bosch Repair in Wheat Ridge
FAQ
Questions Bosch Owners Ask Us
Questions Bosch owners ask us.
Can you repair my Bosch dishwasher?
Yes, Bosch dishwashers are a big part of the work we do. We handle draining problems, leaks and E15 water-in-base errors, drying and heating issues, and units that will not start, using genuine OEM parts.
How much does a repair visit cost?
The diagnostic visit is $85, and that amount is credited toward the repair if you move forward. You get a firm quote before any work begins, so there are no surprises.
Will my Bosch get genuine replacement parts?
Yes, we install genuine OEM parts. They are designed for your appliance and help the repair hold up over time.
What kind of warranty do you offer?
Repairs come with a 90-day parts and labor warranty. If something related to our work acts up during that time, call us and we will make it right.
My Bosch is showing a code like E22 or E15. What does it mean?
Codes point to a specific system, and some can be handled at home while others need a technician. On a dishwasher, E22, E24 and E25 usually mean a drain blockage, so clean the filter, check the hose and reset; E15 means water in the base, so shut off the water and call for service. If all four LEDs flash, turn the power off for two minutes and restart.
Do you service built-in and panel-ready Bosch appliances?
Yes, we work on built-in, panel-ready and fully integrated Bosch units. Your technician takes care with custom panels, cabinetry and flooring when pulling or accessing an appliance.
Which cities do you serve?
We serve 21 cities across the Denver Metro Area and Boulder County from our office in Superior. Call (720) 285-3573 and we will confirm your address and find a time that works.
Get Your Bosch Back to Its Quiet, Reliable Self
Call (720) 285-3573 to schedule a visit with PointLine. Same-day service is often available, we accept cash, major credit cards, Venmo, Apple Pay and checks, and our optional Care Club at $99 a year includes free service calls, a yearly maintenance visit and 10% off labor.
PointLine Appliance Repair is an independent repair company, not affiliated with Bosch.