Local • Family-Owned
Bosch Repair in Lafayette, CO
A family shop in neighboring Superior tests your Bosch where it's built in, finds the failed part and quotes a firm price before any work.
We repair every Bosch appliance
- $85 DiagnosticCredited toward your repair
- 90-Day WarrantyParts & labor
- Open 24/7Same-day service often available
- Local & Family-OwnedBased in Superior
Bosch Repair • Lafayette
Bosch Care From the Next Town Over
Lafayette families who need Bosch repair can book straight with PointLine, working from our single office at 2600 S Rock Creek Pkwy #103 in Superior, just a short drive from your home. We are an independent, family-owned company with no connection to Bosch. That means you deal with the people who answer the phone, show up at the house and stand behind the work. You can book online or call or text (720) 285-3573, and the $85 diagnostic visit is credited toward the repair if you go ahead.
Around Lafayette, a Bosch might be a dishwasher slipped into a remodeled kitchen in a mining-era house near Old Town, or a wall oven and induction cooktop set into the cabinetry of a newer townhome. Either way, these machines are designed to fit tightly and run quietly, with sensors and control boards making decisions you never see. That design rewards a careful diagnosis. Pulling a built-in from its opening takes time and care, and replacing a board when the real fault was a sensor or a clogged filter wastes your money. Your technician tests first, explains what failed and gives you a firm quote before a single part is ordered.
Bosch Appliances
Nine Bosch Machines, Tested Where They Stand
Here is what each type of Bosch appliance tends to run into and the checks your technician makes before naming a cause.
Bosch Refrigerator
Bosch refrigerators, including built-in and counter-depth models, tend to need help when the fresh-food side warms up, frost gathers on the back panel or the ice maker stops filling. We check the defrost heater and sensor, the evaporator and condenser fans, the door seals and the water inlet valve before pointing to any part.
Bosch refrigerator repair in LafayetteBosch Dishwasher
A Bosch dishwasher that stops draining, shows a fault or leaves water standing in the tub usually traces back to the filter, the drain pump, a hose or the leak-protection float in the base. We clean and inspect the sump, run the pump under load, test the heater and circulation and look closely at the door seal, all while protecting the panel or trim around the machine.
Bosch dishwasher repair in LafayetteBosch Washer
Bosch front-load washers can stall partway through a cycle, refuse to drain or spin, or leave water at the door. We open the pump filter, test the drain pump and door lock, inspect the gasket and hoses and check the suspension and bearings when the drum rumbles.
Bosch washer repair in LafayetteBosch Dryer
When a Bosch dryer runs but the clothes stay damp, the cause can be a clogged lint path or vent, a failed heating element or thermal fuse, or a moisture sensor coated with residue. We measure heat output, test the safety thermostats and sensors, check the belt and rollers and confirm the exhaust or condensing system is actually carrying moisture away.
Bosch dryer repair in LafayetteBosch Wall Oven
Bosch wall ovens can heat slowly, miss their set temperature, stay locked after a self-clean or display a code on the control. We test the bake, broil and convection elements, the temperature sensor, the cooling fan and the door latch, then confirm the cavity holds temperature before we call the job done.
Bosch wall oven repair in LafayetteBosch Range & Stove
On a Bosch range, trouble can sit in the burners, the oven or the controls that tie them together, whether that is a burner that clicks without lighting or an oven that never gets hot. We check igniters, burner heads, valves and elements, then test the oven sensor and control board with a meter instead of guessing.
Bosch range & stove repair in LafayetteBosch Cooktop
Bosch gas, electric and induction cooktops fail in very different ways, from an igniter that sparks without lighting to an induction zone that won't recognize a pan. We confirm the cookware and power supply first, then test the igniters, switches, coils, cooling fan and power boards beneath the glass or grates.
Bosch cooktop repair in LafayetteBosch Range Hood
A Bosch range hood that pulls weakly, rattles or ignores its buttons usually points to greasy filters, a worn blower motor, a stuck damper or a failing control or light switch. We clean or inspect the filters, test the motor and controls and follow the duct for blockages that rob suction.
Bosch range hood repair in LafayetteBosch Microwave
Bosch microwaves, including built-in and drawer styles, may run without heating, stop mid-cycle or leave the turntable or drawer motionless. Because these units hold high voltage even after they are unplugged, we discharge and test the magnetron, diode, door switches and drive parts safely before quoting the repair.
Bosch microwave repair in Lafayette
Error Codes
Reading a Bosch Code Before You Book
The tables below are reproduced from Bosch's support pages and sorted by appliance, so you can match the code on your display to the manufacturer's own explanation. Codes marked as safe to try yourself usually involve simple steps like cleaning a filter or restarting a cycle, while codes marked for a pro point to parts, wiring or water that are better left to a technician.
| Code | What it means | Try first | DIY or pro? |
|---|---|---|---|
| E22, E-22Try it yourself | Draining problem — a blocked filter, a blocked drain pump or loose pump cover, a kinked drain hose, or a clogged air gap.Wash the filter, clean out the drain pump and make sure its cover clicks shut, straighten the hose and clear the air gap. Then reset the dishwasher. | Wash the filter, clean out the drain pump and make sure its cover clicks shut, straighten the hose and clear the air gap. Then reset the dishwasher. | Try it yourself |
| E24, E25Try it yourself | Drain blocked — drain pump, kinked drain hose or a clogged air gap.Clean the drain pump and filter and check the drain hose and air gap. If it still shows, call for service. | Clean the drain pump and filter and check the drain hose and air gap. If it still shows, call for service. | Try it yourself |
| E23Call a pro | The drain pump is blocked, clogged or faulty.Clear the drain pump. If the pump itself has failed, it needs a technician. | Clear the drain pump. If the pump itself has failed, it needs a technician. | Call a pro |
| E15Call a pro | Water in the base — the leak protection system has activated.Turn off the water to the dishwasher and call for service. | Turn off the water to the dishwasher and call for service. | Call a pro |
| E14, E16, E17, E18, E200Try it yourself | Water isn't flowing into the dishwasher properly (flow meter, fill system or low water).Make sure the water supply is on and the inlet hose isn't kinked or damaged. | Make sure the water supply is on and the inlet hose isn't kinked or damaged. | Try it yourself |
| E12Try it yourself | Limescale has built up in the heat pump.Descale the dishwasher, and use softening salt if your model has a water softener. | Descale the dishwasher, and use softening salt if your model has a water softener. | Try it yourself |
| E09, E21Call a pro | Heat pump heater fault (E09) or the heat pump is blocked (E21).Reset power at the breaker for 30 seconds. If it returns, call for service. | Reset power at the breaker for 30 seconds. If it returns, call for service. | Call a pro |
| E01, E02, E04Call a pro | Control board or heater electronics fault found in the self-test.Reset power at the breaker for 30 seconds. If it returns, call for service. | Reset power at the breaker for 30 seconds. If it returns, call for service. | Call a pro |
| E06Call a pro | Door sensor circuit fault.Reset power for 30 seconds; if it stays, the door sensor needs a technician. | Reset power for 30 seconds; if it stays, the door sensor needs a technician. | Call a pro |
| E07, E10Call a pro | CrystalDry (zeolite) fan motor or chamber heater fault.This needs a technician. | This needs a technician. | Call a pro |
| E19Call a pro | Detergent dispenser solenoid circuit fault.Reset power for 30 seconds; if it returns, call for service. | Reset power for 30 seconds; if it returns, call for service. | Call a pro |
| E27, E9001Try it yourself | The house power supply to the dishwasher is too low.Reset the breaker for 30 seconds. If it happens again, have an electrician check the voltage. | Reset the breaker for 30 seconds. If it happens again, have an electrician check the voltage. | Try it yourself |
| E0100–E0110Call a pro | Electronics miscommunication.Reset power for 30 seconds; if it stays, call for service. | Reset power for 30 seconds; if it stays, call for service. | Call a pro |
| E6160Call a pro | PowerControl lower spray arm can't find its reference position.Reset power; if it returns, call for service. | Reset power; if it returns, call for service. | Call a pro |
| 4 LEDs flashingTry it yourself | A technical issue (models without a code display).Switch off, unplug or turn off the breaker for at least 2 minutes, then restart. If it happens again, call for service. | Switch off, unplug or turn off the breaker for at least 2 minutes, then restart. If it happens again, call for service. | Try it yourself |
Source: Bosch US — dishwasher error codes. Codes vary by model — check your owner's manual.
| Code | What it means | Try first | DIY or pro? |
|---|---|---|---|
| E18, F18Try it yourself | The drain hose is blocked or kinked.Unkink and clean the drain hose and clean the drain pump. | Unkink and clean the drain hose and clean the drain pump. | Try it yourself |
| E17, F17, F29Try it yourself | Inlet filters are blocked or water pressure is too low.With the tap off, clean the filters in the water supply hose and check the water flow. | With the tap off, clean the filters in the water supply hose and check the water flow. | Try it yourself |
| E16, E34, F16, F34Try it yourself | The door isn't locked properly.Close the door until it clicks and check that nothing is caught. | Close the door until it clicks and check that nothing is caught. | Try it yourself |
| E32, F32Try it yourself | Imbalance detected — spin may slow or stop.Wash large and small items together and close zippers and buttons. | Wash large and small items together and close zippers and buttons. | Try it yourself |
| E:00 / -23Call a pro | Water in the base — the appliance is leaking.Turn off the water tap and call for service. | Turn off the water tap and call for service. | Call a pro |
| E80Call a pro | A fault in the drive circuit.Bosch states this can only be fixed by an authorized technician. | Bosch states this can only be fixed by an authorized technician. | Call a pro |
Source: Bosch US — washer error codes. Codes vary by model — check your owner's manual.
| Code | What it means | Try first | DIY or pro? |
|---|---|---|---|
| E02Call a pro | The ice maker is faulty, or the ice and water controls can't communicate.Reset power at the breaker for 30 seconds. If it stays, call for service. | Reset power at the breaker for 30 seconds. If it stays, call for service. | Call a pro |
| E03Call a pro | Dispenser user interface fault.Reset power at the breaker for 30 seconds. If it stays, call for service. | Reset power at the breaker for 30 seconds. If it stays, call for service. | Call a pro |
| E or D + numberTry it yourself | An operational fault.Switch the refrigerator off, unplug it or turn off the breaker, and reconnect after 5 minutes. If the message is back, call for service. | Switch the refrigerator off, unplug it or turn off the breaker, and reconnect after 5 minutes. If the message is back, call for service. | Try it yourself |
Source: Bosch US — refrigeration error codes. Codes vary by model — check your owner's manual.
| Code | What it means | Try first | DIY or pro? |
|---|---|---|---|
| e011Try it yourself | Touch sensor failure on the oven control panel.Clean and dry the panel, then turn the breaker off for 5 minutes and back on. | Clean and dry the panel, then turn the breaker off for 5 minutes and back on. | Try it yourself |
| e005Call a pro | Communication failure between the user interface and the power board.Turn the breaker off for 5 minutes and back on. If it persists, call for service. | Turn the breaker off for 5 minutes and back on. If it persists, call for service. | Call a pro |
| e101Call a pro | The temperature sensor is malfunctioning.Check the power cord wiring, then reset the breaker. If it persists, call for service. | Check the power cord wiring, then reset the breaker. If it persists, call for service. | Call a pro |
| e126Try it yourself | The door lock is malfunctioning.Cancel Self Clean, wait for the door to unlock, and start Self Clean again. | Cancel Self Clean, wait for the door to unlock, and start Self Clean again. | Try it yourself |
Source: Bosch US — freestanding range error codes. Codes vary by model — check your owner's manual.
| Code | What it means | Try first | DIY or pro? |
|---|---|---|---|
| dETry it yourself | Demo mode is on — the zones don't heat.Turn off the breaker for 30 seconds, then touch any control within 3 minutes. | Turn off the breaker for 30 seconds, then touch any control within 3 minutes. | Try it yourself |
| F2, F4Try it yourself | The electronics overheated and one zone (F2) or all zones (F4) switched off.Let the cooktop cool, then touch any control and keep cooking. | Let the cooktop cool, then touch any control and keep cooking. | Try it yourself |
| F1, F6 (induction)Try it yourself | A cooking zone overheated and switched off to protect the surface.Let it cool, then switch the zone back on. | Let it cool, then switch the zone back on. | Try it yourself |
| F5Try it yourself | Hot cookware is too close to the control panel.Move the pan off the controls, wait a few seconds and touch any control. | Move the pan off the controls, wait a few seconds and touch any control. | Try it yourself |
| F8Try it yourself | A zone ran a long time without any input, so the automatic time limit turned it off.Touch any control and set the zone again. | Touch any control and set the zone again. | Try it yourself |
| U400, E9000, E9010, E9011Call a pro | Supply voltage is outside the normal range, or the cooktop isn't connected correctly.Have the connection and voltage checked — call your utility or an electrician, or call us. | Have the connection and voltage checked — call your utility or an electrician, or call us. | Call a pro |
| D or E + numberCall a pro | An operational fault.Switch the cooktop off and on. If the message comes back, call for service with the exact code. | Switch the cooktop off and on. If the message comes back, call for service with the exact code. | Call a pro |
| All indicators flashingTry it yourself | The control panel is wet or something is covering it.Dry the panel or remove the object. | Dry the panel or remove the object. | Try it yourself |
Source: Bosch US — cooktop and rangetop error codes. Codes vary by model — check your owner's manual.
| Code | What it means | Try first | DIY or pro? |
|---|---|---|---|
| E11Try it yourself | The touch keys aren't working properly — often condensation on the keypad.Dry the control panel, then switch the breaker off for 10 seconds and back on. | Dry the control panel, then switch the breaker off for 10 seconds and back on. | Try it yourself |
| E + numberCall a pro | A malfunction (the control may beep).Press any button to stop the beeping and note the code. If it keeps coming back, switch off the breaker and call for service. | Press any button to stop the beeping and note the code. If it keeps coming back, switch off the breaker and call for service. | Call a pro |
Source: Bosch US — oven and microwave error codes. Codes vary by model — check your owner's manual.
Common Problems
Six Bosch Troubles and Their Usual Suspects
Each row reflects how Bosch appliances are generally built, and your technician confirms which cause applies to your machine through testing before you hear a price.
Dishwasher finishes the cycle but dishes come out wet or cloudy
- Likely causes
- Empty rinse aid dispenser, a weak heating element, a failed water temperature sensor, a clogged filter or blocked spray arms
- What we check
- We check the rinse aid setting, measure heater resistance and fill temperature, and clear and inspect the filter and spray arms.
Refrigerator ice maker has stopped producing ice
- Likely causes
- A frozen fill tube, a failed water inlet valve, a clogged water filter, low supply pressure or a faulty ice maker module
- What we check
- We check water flow at the valve, thaw and inspect the fill tube and run the module through a harvest cycle to watch it work.
Washer won't spin or shakes hard during the spin
- Likely causes
- An unbalanced load, worn shock absorbers, failing drum bearings, a motor or drive fault, or a drain problem that blocks the spin
- What we check
- We check drum play and bearing noise, test the suspension and motor and make sure the washer drains fully before it tries to spin.
Dryer needs two or three cycles to dry a load
- Likely causes
- A restricted vent or lint path, a failed heating element or gas valve coil, a dirty moisture sensor or a clogged condenser on condensing models
- What we check
- We measure temperature at the exhaust, inspect the vent and lint path, test the heat source and clean and test the sensors.
Gas burner won't stay lit or burns with a lazy yellow flame
- Likely causes
- A misaligned burner cap, dirty igniter or burner ports, moisture from a spill or a gas setup problem
- What we check
- We clean and reseat the burner parts, test the igniter and spark module and check the flame pattern and gas setup.
Oven or cooktop control shows a code or stops responding
- Likely causes
- A power interruption, electronics overheated by a blocked cooling fan, a failed sensor or a failing control board or touch panel
- What we check
- We check the supply and reset behavior, test the cooling fan and sensors and only then evaluate the board itself.
Lafayette Homes
What Lafayette Homes Ask of a Bosch
A few plain facts about the town shape where your technician looks first on a Bosch visit.
Old Town houses with modern kitchens
Old Town Lafayette, along Public Road and Simpson Street, mixes historic commercial buildings and mining-era homes with newer townhomes. When a Bosch dishwasher or wall oven goes into an older house, it is fitted inside walls and cabinets that were never planned around it. Wiring, drain connections and cabinet openings can be less standard than in new construction. We check those connections during the diagnosis, because a fault that looks like a failed part can begin with the supply or drain behind the appliance.
Newer subdivisions and tight townhome layouts
Beyond the historic downtown, much of the housing is newer subdivisions and townhomes, where laundry can sit in a closet or hallway and kitchens leave little room around a built-in. A stacked or tucked-in Bosch washer and dryer need clear space to come forward safely, and a dryer vent routed through tight framing deserves a look when drying slows down. We plan the move before anything slides out and protect floors and trim along the way.
Gas cooking at about 5,266 feet
The town sits at about 5,266 feet, and the thinner air at that height changes how gas burns. Bosch gas ranges and cooktops depend on correct setup and clean, properly seated burner parts to hold a steady blue flame. A flame that turns yellow, lifts off the burner or goes out on low deserves a technician's attention rather than a guess.
Premium Appliance Care
Working Inside a Finished Kitchen
For Lafayette homeowners who want Bosch repair they can trust, how we care for your kitchen matters as much as how we fix the appliance, so we follow these habits on every built-in job.
Padding before pulling
Before a panel-ready dishwasher or wall oven leaves its opening, we lay floor protection and cover nearby cabinet faces, panel edges and stone counters. We ease the unit out slowly so leveling legs, trim pieces and countertop corners stay intact.
Respecting the air a built-in breathes
Built-in refrigerators move heat through front grilles and toe-kick vents, and wall ovens and induction cooktops rely on fans to keep their electronics cool. We clear those paths, confirm the fans run and make sure the unit goes back with its airflow unblocked, since trapped heat can bring the same fault right back.
Matched parts, proper steps
We order genuine OEM parts by your model and serial number, because Bosch units that look alike can contain different boards, pumps or sensors. Each repair follows the correct procedure for that appliance, from resetting leak protection to running a full test cycle before we leave.
Why the cheap shortcut isn't cheap
On a luxury built-in, a rushed repair can mean paying for a part you never needed, a scratched custom panel, a chipped counter edge or a supply line kinked behind the cabinet. Testing first and handling the unit with care protects the appliance and the kitchen built around it.
From Our Own Jobs
Real Bosch Repairs From Our Own Jobs
Real photos from our own service calls around the Denver Metro Area — not stock images.
Bosch dishwasher showing an E:15 code 
Bosch dishwasher showing an E:23 code
Repair or Replace?
Another Repair or a New Bosch?
The lifespan chart next to this section, drawn from an NAHB study, gives a rough sense of how long each appliance type tends to last, and it is a fair place to start thinking. Age is only part of the picture, though. A single failed pump, sensor or element on a well-kept Bosch is usually worth fixing, while several major parts failing at once, or a repair price that creeps toward the cost of a new unit, can tip the balance the other way. Your technician gives you the firm quote and an honest read on the machine so you can decide with real numbers in hand.
Built-ins change the math in favor of repair. A replacement dishwasher or wall oven has to fit your existing cutout, trim and custom panel, and a mismatch can turn a simple swap into cabinet work, new stone or a panel you have to order and finish. Keeping the appliance you have avoids that ripple effect. Whatever you choose, the $85 diagnostic is credited toward the repair, and the work carries our 90-day parts and labor warranty.
Typical lifespan by appliance
| Refrigerator | ~13 yrs |
|---|---|
| Dishwasher | ~9 yrs |
| Washer | ~10 yrs |
| Dryer | ~13 yrs |
| Wall Oven | ~13 yrs |
| Range & Stove | ~13–15 yrs |
| Microwave | ~9 yrs |
Source: NAHB study of home component life. Any brand; real life varies with use and care.
Google Reviews
What Our Customers Say
5.0Every review on Google is five stars.
“I had my GE washing machine repaired and I am so very grateful for your service. It was a far more complicated repair than originally thought, but I cannot stress enough how much I appreciated the openness and honesty. Everything was handled with kindness and tact. I highly recommend this company for all of your appliance repair needs!”
John H.August 2026 · Google “Nick is professional, highly-skilled, and did a great job troubleshooting and fixing our refrigerator. Our Whirlpool refrigerator was dispensing water randomly. Nick figured out the root cause, ordered a part, and then fixed it the day the part arrived. With such a potentially deleterious issue, Nick took care of it quickly, and effectively. We are grateful. I will certainly call upon his expertise again.”
Brian R.August 2026 · Google “We were vey happy with PointLine’s repair service. Nick was able to come out on short notice and diagnosed the issue with our fridge, ordered the right part, and completed the repair - all within 24 hours. Highly recommend. Professional, efficient, and cost effective.”
Camila P.August 2026 · Google
Membership
PointLine Care Club
One service call is $85. For $99 a year, every service call is free.
- Free service calls all year — no $85 fee
- 1 free maintenance visit a year
- 10% off labor on every repair
$99/ year
One household · renews yearly · cancel anytime before renewal
Property manager or landlord? See our Property Care Club →
Lafayette Service Area
Bosch Repair Across Lafayette
ZIP codes 80026 and the neighboring communities we serve every week.
Managing rentals? See the Property Care Club.
FAQ
Bosch Questions From Around 80026
Straight answers for Bosch owners in Lafayette.
Is PointLine connected to Bosch?
No, we are an independent, family-owned repair company with no affiliation with Bosch. We repair Bosch appliances using genuine OEM parts and our own testing.
My Bosch is showing an error code. Can I look it up first?
Yes, the tables on this page come from Bosch's support pages and show whether a simple step is worth trying. If the code returns, points to a pro or comes with water on the floor, stop using the appliance and book a visit.
Can you repair a Bosch dishwasher behind a custom panel or a built-in wall oven?
Yes, we service panel-ready and built-in Bosch appliances. We protect the panel, cabinets and counters before the unit comes out of its opening.
The Bosch app sent an alert. Is that enough to diagnose the problem?
It's a helpful clue, but not a diagnosis by itself. Share the message when you book, and your technician confirms the cause with hands-on testing.
Will you use genuine Bosch parts?
Yes, we install genuine OEM parts matched to your model and serial number. Every repair carries our 90-day parts and labor warranty.
How soon can a technician reach Lafayette?
Same-day service is often available from our Superior office, but we can't promise it on any particular day. Booking early in the day gives us a better chance.
Do you cover all of 80026?
Yes, we serve the entire 80026 ZIP code, from Old Town to the newer subdivisions. We also work in Louisville, Erie, Superior, Broomfield, Northglenn and Boulder.
Which Bosch is slowing down your Lafayette week?
Book online or call or text (720) 285-3573 for a $85 diagnostic credited toward the repair, and ask about the PointLine Care Club at $99 a year for ongoing household coverage.
PointLine Appliance Repair is an independent repair company, not affiliated with Bosch.