Skip to content
PointLineAPPLIANCE REPAIR

Lafayette, Colorado

Dishwasher Repair in Lafayette, CO

Drains that stall, doors that drip, glasses that come out hazy: we find the cause in your kitchen and quote a firm price first.

Dishwasher Repair in Lafayette, Colorado

Dishwasher Repair • Lafayette

When the Plates Pile Up and the Machine Won't Help

A dishwasher rarely fails all at once. It drains a little slower, leaves a faint film on the tumblers, or starts humming without filling, and then one evening you open the door to a tub of gray water. We repair built-in, panel-ready and drawer dishwashers in Lafayette houses, condos, townhomes and rentals. PointLine is a small, family-owned company working out of one office in Superior, the town right next door, so a trip to your kitchen is a short one for us.

This is an appliance worth fixing properly because of where it lives. It sits under a counter, tied into a hot water line, a drain and an electrical circuit, and surrounded by cabinets and flooring that absorb a slow leak without complaint until the damage shows. Swapping parts on a hunch can miss the actual problem and let water keep seeping into the subfloor unnoticed. Your technician tests the machine until the cause is confirmed, installs genuine OEM parts, and gives you a firm price before any work begins.

Right Now

Water on the Floor? Take These Steps Now

Taking a few calm steps right away keeps your floors and cabinets protected and helps speed up the repair.

  1. 1Cut the ElectricityTurn off the breaker that powers the dishwasher, or unplug it if you can easily reach the cord under the sink. Water and live wiring shouldn't share the floor.
  2. 2Close the Supply LineFind the valve under the kitchen sink on the line running to the dishwasher and turn it fully closed. This stops a failed inlet valve from feeding the leak.
  3. 3Dry Everything and Leave the Cycle OffSoak up the water, lift rugs and lay towels along the cabinet base. Resist restarting the cycle to see if it happens again, because each run pushes more water under the cabinets.
  4. 4Photograph the Model LabelOpen the door and look along the edge of the inner door or the tub frame to find the rating sticker. Sending a clear photo of the model and serial numbers lets your technician show up prepared.

Common Problems

Six Ways a Dishwasher Lets You Down, Traced to the Source

These causes describe how dishwashers are built in general. Your technician confirms the actual fault in your kitchen with testing before anything is quoted or replaced.

  • Gray water sitting in the tub

    Likely causes
    A clogged filter, a jammed or failed drain pump, a stuck check valve, or a blockage in the drain hose, air gap or disposal connection can all leave water sitting in the tub. When a garbage disposal has just been put in and nobody removed its knockout plug, the dishwasher has no way to drain.
    What we check
    We pull the filter, listen to and test the drain pump, inspect the check valve and follow the hose to the sink connection.
    Typical fix
    Usually the fix comes down to clearing a blockage or putting in a genuine replacement drain pump or check valve.
  • Food stuck to plates after a full cycle

    Likely causes
    Weak cleaning is often traced to spray arm jets blocked by debris or scale, a dirty filter, a struggling wash pump, water that comes in lukewarm, or using too much or too little detergent. Overloading that blocks the arms produces the same result.
    What we check
    We check the spray arms for free rotation and clear jets, measure water temperature and test the wash motor's output.
    Typical fix
    Cleaning or replacing spray arms, servicing the filter, or replacing a worn wash pump usually restores clean dishes.
  • Puddles under the door or toe kick

    Likely causes
    A worn door gasket, leaking pump seals, a dripping inlet valve, a loose hose connection, a cracked tub or an overfill can all put water on the floor. Sudsing from the wrong detergent can also push water past the door.
    What we check
    We trace the water's path with the toe kick off, inspect seals and connections and test the fill level and float.
    Typical fix
    Typical repairs include a new gasket, pump seal or inlet valve, or a tightened or replaced hose.
  • Humming with no water coming in

    Likely causes
    A failed water inlet valve, a float switch stuck in the up position, a partly closed supply valve or a clogged inlet screen will all keep the dishwasher from filling. The control may simply think the tub is already full.
    What we check
    We test the inlet valve's coil, check the float for free movement and confirm water pressure at the supply.
    Typical fix
    Most fill problems are solved by replacing the inlet valve or by freeing or replacing the float switch.
  • No lights, no start or a flashing code

    Likely causes
    A door latch that doesn't register as closed, a blown thermal fuse, a tripped breaker or GFCI, or a failing control board can keep the machine from powering on. Error codes point to a system but don't always name the failed part.
    What we check
    We read the code, test the latch switches, check power at the machine and test the fuse and control outputs.
    Typical fix
    Fixes range from a new latch assembly or thermal fuse to a replacement control board when testing confirms it.
  • Everything still wet at cycle's end

    Likely causes
    Damp dishes at the end of a cycle usually point to an empty rinse aid dispenser, a failed heating element, a faulty vent or drying fan, or the heated-dry option being turned off. Plastics hold water more than glass on almost any machine.
    What we check
    We check the cycle settings and dispenser, then test the heating element, high-limit thermostat and vent or fan.
    Typical fix
    Refilling rinse aid solves many cases; otherwise a new heating element, thermostat or vent assembly does.

Spots, Film & Water

Haze, Spots and the Path Water Takes

Cloudy glasses usually come from how water enters, circulates and leaves the machine rather than from a broken part. Some of this is routine owner care, and some of it calls for a technician.

  • A Filter That Needs Your Hands

    Many current dishwashers use a manual-clean filter seated under the lower spray arm instead of a self-cleaning grinder. When it clogs, the machine recirculates dirty water and redeposits grit on your dishes. Check your owner's manual for how to twist the filter out, rinse it and how often it needs cleaning. If the filter housing is cracked or won't seat, call us rather than running the machine without it.

  • Rinse Aid and a Measured Detergent Dose

    In dry high-country air, rinse aid matters because it lets water sheet off glass rather than bead into drops that dry into spots. Keep the dispenser full and set it as the manual suggests. More detergent isn't better: too much can leave a chalky film and cause sudsing, while too little lets food and minerals stay behind. Follow the dosing on the package and in your manual.

  • Start Warm, Watch for Scale

    A lot of dishwashers draw from the kitchen hot water line, so letting the sink tap run until it's hot before starting a cycle helps the first fill start out warm, particularly in winter. Minerals in tap water build up as scale on jets, the tub and the heating element over time. A dishwasher cleaner used as the manufacturer directs can loosen light buildup. Heavy scale on the element or film that returns right after cleaning is a job for your technician.

  • Where the Dirty Water Goes

    Used water leaves the dishwasher through a drain hose that runs to either the garbage disposal or an air gap on the sink deck. It's safe for you to run the disposal before starting a cycle and to lift off the air gap cap to clear any debris. A kinked hose behind the machine or a drain loop installed incorrectly lets dirty water drift back into the tub. Those require pulling the dishwasher out, so leave them to us.

From Our Own Jobs

Real Dishwasher Repairs From Our Own Jobs

Real photos from our own service calls around the Denver Metro Area — not stock images.

  • Stainless Maytag built-in dishwasher in white cabinets
    Maytag built-in dishwasher
  • Bosch dishwasher control panel showing an E:15 code
    Bosch dishwasher showing an E:15 code
  • Front of a dishwasher detergent and rinse aid dispenser held in a gloved hand
    Detergent and rinse aid dispenser, front side

Recognize the Problem?

Book Dishwasher Repair in Lafayette

Tell us what's happening — we'll call you back to confirm a time.

(720) 285-3573

Lafayette Homes

Mining-Era Kitchens, Dry Air and Shared Walls

Here is how a few details about Lafayette, read alongside general dishwasher knowledge, shape where your technician looks first.

  • Historic Houses Next to Newer Builds

    Old Town Lafayette mixes mining-era homes with newer townhomes, and the rest of the city adds subdivisions built much later. In an older house, the dishwasher almost always arrived long after the kitchen was designed, so its water line, drain and wiring were added to a space never planned for them. Your technician pays close attention to the shutoff valve, the drain routing and the electrical connection in these kitchens. In newer homes the concern is different: builder-installed machines of similar age tend to wear out their pumps, valves and gaskets around the same time.

  • Minerals in Everyday Tap Water

    Like tap water almost everywhere, the water feeding your dishwasher carries dissolved minerals, and heat leaves them behind as film and scale. Over time that buildup can narrow spray arm jets, coat the heating element and leave glassware looking cloudy even when it's clean. Rinse aid, a correct detergent dose and a clean filter keep most of it in check. When film appears suddenly or grows worse quickly, it's worth having the fill and heating systems tested.

  • High, Dry Air and Attached Homes

    At 5,266 feet the air is thin and generally dry, so droplets left on glass evaporate fast and leave their minerals as spots whenever rinse aid runs out. Winter makes the incoming water colder, which matters for any machine that relies on the hot line to start its first fill warm. In townhomes and attached units, a dishwasher leak doesn't always stay in your kitchen, since water can travel under shared floors and walls. That's one more reason to shut a leaking machine down promptly instead of running it until the weekend.

Error Codes

Dishwasher Error Codes by Brand

Official codes from each manufacturer, with what to try first, are on our dishwasher repair page. Common ones at a glance:

  • LG

    IE · OE · bE and more

  • Bosch

    E15 · E16 · E22 and more

  • Samsung

    4C · 5C · LC and more

  • GE · Monogram

    C1 · C3 · C4 and more

  • Whirlpool · Maytag · KitchenAid · Amana · JennAir

    F9E1 · F9E2 · F8E4 and more

  • Frigidaire

    i20 · i40 · CL and more

  • Thermador

    E22 · E24 · E23 and more

  • Miele

    F11 · F12 · F14 and more

  • Viking

    E:01 · E:02 and more

See all dishwasher error codes

Repair or Replace?

Is One More Repair the Smart Call?

Alongside this section you'll find the typical lifespan of a dishwasher, based on a National Association of Home Builders study. Use it as a reference point rather than an expiration date, since how often you run the machine and how well it's been cared for change the picture. The practical question is how the repair compares to the price of a new unit plus installation. Replacing a pump, valve, gasket or latch on a sound, middle-aged machine usually makes sense, while a failed control board on an old unit with a rusting tub may not.

Installation tilts the math too. Replacing a built-in or custom-panel dishwasher can get expensive, since a new model might not fit the opening, the panel mounts or the look of your cabinets, so repair is usually the better fit for those. On the flip side, a very old machine may use more water and energy than today's designs, and parts for some discontinued models become harder to track down. Your technician will tell you plainly what the diagnosis shows so you can decide with real information.

Typical dishwasher lifespan

~9 yrs

Source: NAHB study. Real life varies with brand, use and maintenance.

Built-In & Luxury

Fully Integrated and High-End Machines, Handled Gently

Panel-ready dishwashers hide behind a door that matches the surrounding cabinets, held on with brackets and screws and balanced by hinge springs set for that panel's weight. We service panel-ready and premium dishwashers, including drawer models, from Miele, Bosch, Thermador, ASKO, Viking, JennAir, Dacor and Monogram. When a repair means sliding the machine out, your technician protects the flooring and the panel, removes the unit without stressing the cabinetry and reinstalls it level and square. Hinge tension gets checked before we leave so the door doesn't slam or drift.

Premium machines often use their maker's own flood-protection systems, water sensors and electronic controls, and each reports faults in its own way. Guesswork on these gets expensive, so your technician works from the brand's diagnostic approach and confirms the failed part before quoting. We install genuine OEM parts, which keeps fit, sealing and sensor readings the way the manufacturer designed them. That care matters most on a machine you can't easily replace without changing the kitchen around it.

Before You Call

Five Safe Things to Check Before Calling Us

  1. 1Reset the breaker or GFCI outletA healthy dishwasher can seem dead just because its circuit tripped, and a reset only takes a few seconds.
  2. 2Clear a control lock or delay startA child lock or an accidental delay setting can stop a working machine from starting, and the manual explains how to turn either off.
  3. 3Rinse the filterFood caught behind it leads to standing water, odors and gritty dishes, and cleaning it is a normal part of owner upkeep.
  4. 4Run the disposal and check the air gapA full disposal or a plugged air gap can stop drainage before the pump ever gets a chance.
  5. 5Spin the spray arms by handA tall pan or dropped utensil that blocks an arm leaves whole sections of the rack unwashed.

Brands

Dishwasher Brands on Our Service List

Our team works on everyday dishwashers from Whirlpool, GE, KitchenAid, Maytag, Frigidaire, LG and Samsung, along with premium and European brands. Pick your brand below to see notes on particular models.

What to Expect

Your Repair Visit, Start to Finish

Your technician arrives in the window you picked, hears what you've noticed, then tests the fill, wash, drain, heating and controls until the fault is confirmed. We explain the problem clearly and give you a firm price before starting, and once the repair is done we run a cycle to make sure it fills, washes and drains properly.

Diagnostic visit
$85Credited toward the repair if you go ahead
Your price
Firm quoteApproved by you before any work
Warranty
90 daysParts and labor
Parts
Genuine OEMMatched to your model number

We accept

Cash, Major credit cards, Venmo, Apple Pay, Checks

Book in Lafayette (720) 285-3573

Google Reviews

What Our Customers Say

5.0Every review on Google is five stars.

Read more reviews on Google
  • “Nick was excellent. He was able to come out the same day as I discovered that my 21 year old refrigerator had been leaking for weeks or months. He was able to diagnose the problem quickly, ordered the part immediately, and was available within a couple of days to install the new part and finish the repair work. He was on time for both appointments, and called in advance. It’s hard to find people like this these days, I will highly recommend him and use him again if I have additional appliance failures.”

    Noreen B.June 2026 · Google
  • “Nick was great! Professional, fair and arrived same day. Walked me through everything and with no surprises. I highly recommend him.”

    Michael D.July 2026 · Google
  • “We had PointLine Appliance Repair diagnose and repair our 3-year old GE Washing Machine that had ceased to complete the spin dry cycle. Nick was polite and professional. He correctly identified the electronic part that needed to be replaced. He replaced the part and the washing machine now runs like new again. We highly recommend PointLine Dominance Repair!”

    Lorin C.October 2026 · Google

Membership

PointLine Care Club

One service call is $85. For $99 a year, every service call is free.

  • Free service calls all year — no $85 fee
  • 1 free maintenance visit a year
  • 10% off labor on every repair

$99/ year

One household · renews yearly · cancel anytime before renewal

Property manager or landlord? See our Property Care Club →

FAQ

Dishwasher Questions From Lafayette Homeowners

Dishwasher questions from Lafayette homeowners.

Still have a question?

Give us a call — we'll be glad to help.

(720) 285-3573

Is my 80026 address inside your service area?

Yes, we serve the entire 80026 ZIP code, from Old Town Lafayette out to the newer subdivisions and townhome neighborhoods. Our service area also includes Louisville, Erie, Superior, Broomfield, Northglenn and Boulder.

Our Old Town house has a dishwasher squeezed into a kitchen built long before dishwashers. Can you work on it?

Yes, and your technician will take extra care with the plumbing and wiring that were added later. In kitchens like these, the shutoff valve, drain routing and electrical connection get a close look, since a weak point there can cause trouble even after the machine itself is fixed.

We live in a townhome. How urgent is a small leak?

Treat it as urgent and stop using the machine until it's checked. In attached homes, water that slips under the cabinet can travel beneath shared floors and walls, and a slow drip often does its damage out of sight.

Does the elevation here make my glasses spot more?

It can contribute, because the dry air at this altitude evaporates droplets quickly and leaves minerals behind. Keeping rinse aid filled, cleaning the filter and starting with hot water at the sink usually make a clear difference.

Is it possible for a landlord to schedule a repair for a rental property in town?

Yes, an owner or property manager can book online or by call or text. Just arrange for someone to let your technician in and to approve the firm quote before work begins.

My dishwasher drains slowly but still works. Can it wait?

It can usually wait a few cycles if there's no water on the floor, but don't ignore it. First rinse the filter and run the disposal; if water still lingers in the tub afterward, book a visit before a slow drain becomes a full blockage.

Ready to stop hand-washing every dinner dish?

Book online or call or text (720) 285-3573, and we'll come over from Superior, find the real cause and give you a firm price before any work begins.

Call Now Book Online