Erie, Colorado

Dishwasher Repair in Erie, CO

Standing water, leaks, cloudy glasses or a dark panel, diagnosed in your kitchen by a family company based next door in Superior.

Schedule Service (720) 285-3573

What's your dishwasher doing?

Firm Quote FirstApproved by you before any work
90-Day WarrantyParts & labor
Open 24/7Same-day service often available
Local & Family-OwnedBased in Superior

Dishwasher Repair • Erie

Clean Dishes Again, Without the Guesswork

A dishwasher that stops halfway, leaves a puddle or turns out plates dirtier than they went in has a way of taking over the evening. Whether you live in a house, townhome, condo or rental in Erie, PointLine can fix your dishwasher, with service from Old Town Erie around Briggs Street out to Vista Ridge, Colliers Hill, Flatiron Meadows and Candlelight Ridge. We're a small, family-owned company working out of one office on Rock Creek Parkway in neighboring Superior, so your call reaches people who live and work close by. Before anything gets started, your technician will test the dishwasher, walk you through what went wrong and hand you a firm quote.

This appliance is tucked under a counter, plumbed to a hot water line, wired to a circuit and boxed in by cabinets and flooring that don't forgive slow leaks. A quick fix that treats only the symptom, like clearing a drain without asking why it clogged, tends to bring the same trouble right back. We trace the fault to its source, replace what's actually worn with genuine OEM parts, and back the work with a 90-day parts and labor warranty. The $85 diagnostic visit is credited toward the repair when you go ahead.

Right Now

Leaking or Flooded? Start Here

Taking care of power and water first keeps a small leak from turning into a cabinet or flooring problem.

1Kill the PowerTurn off the circuit breaker that serves the dishwasher, or unplug it if the cord is within easy reach under the sink. Don't stand in water to do this; if the floor near the outlet is wet, go straight to the breaker.
2Stop the WaterUnder the kitchen sink, find the valve on the line that feeds the dishwasher and turn it until it's fully closed. That keeps a stuck inlet valve from adding more water.
3Dry Out and Hold OffTowel up the floor, move rugs away, and leave the cycle alone, since restarting a leaking machine only pushes more water under the cabinets. Water sitting in the tub can be bailed out with a cup and sponge if you need the space.
4Find the Model NumberThe rating label usually sits on the side edge of the door or on the tub frame, and a clear photo of it is all you need. Sharing that photo when you book helps your technician come prepared with the right information.

Common Problems

When the Dishwasher Acts Up: Symptoms, Causes, Fixes

Each entry below draws on how dishwashers are generally built; nothing gets replaced until your technician has tested the suspect part and you've approved the price.

Water pooled in the tub after the cycle
Likely causes
A clogged filter, a jammed or failed drain pump, a stuck check valve, or a blocked drain hose, air gap or disposal connection can all trap water.
What we check
We run a drain test, inspect the filter and sump, listen to the pump, and trace the hose to the disposal or air gap.
Typical fix
Clearing a blockage often solves it. Otherwise we replace the drain pump or check valve with a genuine part.
Food residue left on plates
Likely causes
Spray arm jets plugged with debris or scale, a dirty filter, a weak wash pump, lukewarm incoming water or a detergent dose that's off can all cut cleaning power.
What we check
We check spray arm rotation and jets, measure the water temperature, and watch the wash pump during a cycle.
Typical fix
Cleaning or replacing the spray arms and filter handles many cases. A failing wash motor gets replaced.
Puddle at the base of the door
Likely causes
A worn or torn door gasket, leaking pump seals, a dripping inlet valve, a cracked tub or an overfill from a stuck float are the usual sources.
What we check
We inspect the gasket and door alignment, look beneath the tub with the kick plate off, and check the fill level.
Typical fix
Common fixes involve replacing a gasket, seal kit, inlet valve or float switch. A cracked tub usually points toward replacement.
No water during fill
Likely causes
A failed water inlet valve, a float switch stuck in the raised position, a partly closed supply valve or a clogged inlet screen will block filling.
What we check
We confirm supply at the valve, test the inlet valve solenoid for power and continuity, and make sure the float moves freely.
Typical fix
Most of these end with a replacement inlet valve or float switch. Sometimes the fix is simply opening the supply fully.
Panel dark, blinking a code or won't begin
Likely causes
If the machine won't make a sound, the cause may be a door latch that isn't reading as closed, a blown thermal fuse, a tripped breaker or GFCI, or a control board that's on its way out.
What we check
We verify power at the unit, read any fault code, test the latch switch and fuse, then check the board's outputs.
Typical fix
Latches and fuses are common, modest repairs. A control board is replaced only after the other parts test good.
Wet dishes at cycle's end
Likely causes
Dishes that come out damp can point to an empty rinse aid dispenser, a failed heating element, a faulty vent or drying fan, or the heated-dry setting being turned off.
What we check
We check the rinse aid setting, test the heater and its thermostat, and confirm the vent or fan is working.
Typical fix
Refilling rinse aid sometimes does the trick. Otherwise we replace the element, fan or vent assembly.

Spots, Film & Water

Getting to Sparkling: The Water Behind the Wash

Before suspecting a failed part, it pays to look at how water gets in, how clean it stays and how it leaves. Most of the steps below are routine owner care.

A Filter You Rinse Yourself
Many current dishwashers use a filter you remove by hand, usually under the lower spray arm, rather than a self-cleaning grinder. When it clogs, dirty water recirculates over your dishes and leaves grit and film. Your owner's manual shows how to twist it out and how often to rinse it. If the filter is cracked or the sump beneath it holds debris you can't reach, hand that job to your technician.
Rinse Aid and Measured Detergent
Rinse aid helps water run off glass in a sheet instead of standing in drops that dry into spots. Keep the dispenser filled and set it as the manual suggests. Detergent does its job at the recommended dose; too much can leave a residue, while too little can't keep up with a full load. If spotting persists with both dialed in, the cause may be heat or water flow.
Hot Water and Mineral Scale
Many dishwashers fill from the kitchen hot line, so running the faucet until it turns hot before you start helps the first fill begin warm., minerals in any water supply can gradually build up as scale on spray arms, the heater and the tub. A dishwasher cleaner or a cleaning cycle described in your manual can help with light buildup. Scale that has plugged spray jets or coated the heater is something we can clear or replace during a visit.
The Drain Connection Under the Sink
Dirty water drains out through a hose that runs either to the garbage disposal or to an air gap mounted on the sink deck. Two checks you can safely do yourself: run the disposal before starting a cycle, and pop off the air gap cap to clear out any debris. A newly installed disposal with its knockout plug still in place will block draining entirely, a general installation issue worth knowing about. Kinked hoses behind the machine, or water backing up despite a clear air gap, call for your technician.

From Our Own Jobs

Real Dishwasher Repairs From Our Own Jobs

Real photos from our own service calls around the Denver Metro Area — not stock images.

Bosch dishwasher showing an E:23 code
Detergent dispenser out of the door — actuator side
Detergent and rinse aid dispenser, front side
Maytag built-in dishwasher

Recognize the Problem?

Book Dishwasher Repair in Erie

Tell us what's happening — we'll call you back to confirm a time.

(720) 285-3573

Erie Homes

Reading the Dishwasher Through the House Around It

In Erie, the town's steady growth, the families who live here and the high altitude all shape how a dishwasher wears over the years.

Busy Family Kitchens
Many homes here are full family households, and with that many people at the table, the dishwasher often runs at least once a day. Heavy use wears the parts that move and seal: door gaskets, latch mechanisms, pump seals and spray arm bearings. Filters also fill faster when the machine handles a full family's worth of plates, which is why a sluggish drain is often the first warning sign. On a hard-working machine, your technician checks those wear parts before suspecting the electronics.
Original Machines in Newer Houses
A large share of the town's housing went up during its growth since 2000, so plenty of kitchens still have the dishwasher the builder installed. Builder-grade units reaching middle age tend to show familiar patterns, such as a tired inlet valve, a drain pump straining against old debris or a latch that no longer registers. Repairing one of these can make good sense when the tub and racks are still sound, and we'll tell you plainly if they aren't. Remodeled kitchens often hold newer, sensor-driven models that call for a different approach to diagnosis.
Dry Air at About 5,100 Feet
At this elevation the air is thin and generally dry, so water left on glassware evaporates quickly and leaves its minerals behind as spots. Rinse aid matters more in these conditions because it helps water sheet off before it can dry in droplets. Water also boils at a lower temperature at altitude, though dishwashers wash below boiling and rely on their own heaters. When dishes come out spotty, we look at the rinse aid setting, the heater and the incoming water temperature together.

Error Codes

Dishwasher Error Codes by Brand

Official codes from each manufacturer, with what to try first, are on our dishwasher repair page. Common ones at a glance:

LG
IE · OE · bE and more
Bosch
E15 · E16 · E22 and more
Samsung
4C · 5C · LC and more
GE · Monogram
C1 · C3 · C4 and more
Whirlpool · Maytag · KitchenAid · Amana · JennAir
F9E1 · F9E2 · F8E4 and more
Frigidaire
i20 · i40 · CL and more
Thermador
E22 · E24 · E23 and more
Miele
F11 · F12 · F14 and more
Viking
E:01 · E:02 and more

See all dishwasher error codes

Repair or Replace?

Is This Dishwasher Worth Another Repair?

Beside this section you'll find the typical service life a National Association of Home Builders study gives for dishwashers; treat it as a rough benchmark, since your machine's actual life depends on use and care. Age matters, but condition matters more. A machine with a solid tub, straight racks and a single failed pump is a very different case from one with rust in the tub and a string of repeated faults. We compare what the repair will cost with the price of a similar new dishwasher and let you know which option we'd lean toward.

Installation shifts the math too. A dishwasher behind a custom panel or fitted snugly into cabinetry can be costly to swap, because a new model may not match the opening, the panel mounts or your design, so those situations usually favor repair. On the other side, an older unit may use more water and energy than current models, and parts for discontinued machines can become scarce. If a repair doesn't make sense, we'll say so before you spend money on one.

Typical dishwasher lifespan

~9 yrs

Source: NAHB study. Real life varies with brand, use and maintenance.

Built-In & Luxury

Integrated and High-End Machines Behind Cabinet Doors

We repair panel-ready and premium dishwashers from Miele, Bosch, Thermador, ASKO, Viking, JennAir, Dacor and Monogram, along with drawer-style models. Fully integrated units hide behind a door panel matched to your cabinets, attached with brackets and screws, and their hinges are tensioned to carry that extra weight. Pulling one out means protecting the panel, the neighboring cabinets and the floor, then reinstalling with leveling and hinge tension set correctly. Rushed removal is how chipped panels and doors that drop open happen.

Premium machines often rely on their maker's own flood-protection systems, water sensors and electronic controls, each reporting faults in its own way. Diagnosis starts with reading those codes and testing the components they point to, not swapping parts on a hunch. We install genuine OEM parts so seals, sensors and boards match what the machine was engineered around. The same firm quote and 90-day warranty apply whether yours is a basic built-in or a concealed premium model.

Premium brands we repair

Before You Call

Worth Checking on Your Own First

1Look at the breaker and any GFCI outletA tripped circuit can make a perfectly good dishwasher look dead, and resetting it costs nothing.
2Make sure the door latches and no lock is onA door that isn't fully closed, a control lock or an accidental delay start will keep a cycle from running.
3Rinse the filterTrapped food behind it causes standing water, odors and gritty dishes, and cleaning it is routine owner maintenance.
4Clear the disposal and air gapA full disposal or a plugged air gap stops drainage before the pump can do its work.
5Turn the spray arms by handAn arm blocked by a tall pan or a dropped utensil leaves whole sections of the rack unwashed.

Brands

Dishwasher Brands in Our Repair Lineup

Your technician works on Whirlpool, GE, KitchenAid, Maytag, Frigidaire, LG and Samsung as readily as Bosch, Miele and the other premium names. Select your brand below to see notes on specific models.

What to Expect

What Happens When We Arrive

Once you've picked an arrival window, your technician comes ready to hear what's been going on, then tests fill, wash, drain, heat and controls until the fault is confirmed. You get a plain explanation and a firm quote, and the work starts only after you say yes.

Diagnostic visit: $85Credited toward the repair if you go ahead
Your price: Firm quoteApproved by you before any work
Warranty: 90 daysParts and labor
Parts: Genuine OEMMatched to your model number

We accept

Cash, Major credit cards, Venmo, Apple Pay, Checks

Book in Erie (720) 285-3573

Google Reviews

What Our Customers Say

5.0Every review on Google is five stars.

PointLine Care Club

One service call is $85. For $99 a year, every service call is free.

Free service calls all year — no $85 fee
1 free maintenance visit a year
10% off labor on every repair

$99/ year

Join the Care Club What's included

One household · renews yearly · cancel anytime before renewal

Property manager or landlord? See our Property Care Club →

Service Area

Erie ZIP Codes We Serve

Dishwasher Repair at homes, condos and rentals in every part of Erie.

80516
80504
80026

Including Old Town Erie, Vista Ridge, Colliers Hill, Flatiron Meadows, Candlelight Ridge.

Nearby

All appliance repair in Erie Dishwasher Repair across Denver Metro

Related Repair Guides

FAQ

What Erie Homeowners Want to Know About Dishwashers

Dishwasher questions from Erie homeowners.

Still have a question?

Give us a call — we'll be glad to help.

(720) 285-3573

Which ZIP codes around Erie do you cover?

We serve 80516 along with the parts of 80504 and 80026 that take in Erie addresses. That covers homes on the Weld County side of town as well as the Boulder County side. If you live near a boundary, enter your address when you book and we'll confirm.

Our house still has its original builder dishwasher. Fix it or replace it?

That depends more on the condition of the tub and racks than on age alone. If those are sound and the failure is a pump, valve or latch, repair is often reasonable. If the tub is rusting or several parts are failing at once, we'll tell you replacement is the smarter spend.

Why do my glasses come out spotty even after switching detergents?

Spotting usually comes from rinse aid, water temperature or mineral buildup rather than the detergent brand. Dry air at around 5,100 feet makes droplets evaporate quickly and leave minerals behind. Fill the rinse aid, run the sink hot before starting and clean the filter; if spots continue, the heater or spray arms may need a look.

I own a rental home in town. Can the repair happen while I'm away?

Yes, a landlord or property manager can book and approve the work while a tenant or other contact lets your technician in. We share the diagnosis and firm quote with whoever authorizes the repair before anything is done.

Can you service a Bosch or Miele hidden behind a cabinet panel?

Yes, we repair panel-ready and premium dishwashers, including fully integrated models. Your technician removes and reinstalls the unit with care for the custom panel and hinge tension, and uses genuine OEM parts.

Is a small drip something that can wait?

It's safer to stop running the machine until it's checked, because a slow leak can soak the subfloor and cabinet base without showing much on the surface. Close the supply valve under the sink if the drip continues and book a visit; same-day service is often available, though we can't promise it.

Other Repairs We Handle in Erie

Want Your Evenings Back From the Sink?

Book online or call or text (720) 285-3573, and we'll come over from Superior to find the cause and give you a firm quote before any work starts.

Schedule Service (720) 285-3573

Dishwasher Repair in Erie, CO

Clean Dishes Again, Without the Guesswork

Leaking or Flooded? Start Here

When the Dishwasher Acts Up: Symptoms, Causes, Fixes

Water pooled in the tub after the cycle

Food residue left on plates

Puddle at the base of the door

No water during fill

Panel dark, blinking a code or won't begin

Wet dishes at cycle's end