Local • Family-Owned
Maytag Appliance Repair in Denver Metro Area
Thoughtful service for your Maytag washer, dryer, refrigerator, dishwasher, range and more.
We repair every Maytag appliance
- $85 DiagnosticCredited toward your repair
- 90-Day WarrantyParts & labor
- Open 24/7Same-day service often available
- Local & Family-OwnedBased in Superior
Maytag Repair
Dependable Help When a Maytag Stops Pulling Its Weight
Maytag appliances tend to be the everyday workhorses of a home: the washer that runs several loads a week, the dryer that handles towels and jeans, and the dishwasher that clears the dinner table. When one of them stalls, the whole household feels it. PointLine is a small, family-owned company based in Superior, and we bring the same steady approach to every Maytag we work on.
Your technician starts with a $85 diagnostic visit, and that fee is credited toward the repair if you move forward. Once the cause is found, you get a firm quote before any work begins, so there are no surprises. We install genuine OEM parts, back the repair with a 90-day parts and labor warranty, and same-day service is often available depending on the schedule.
Maytag Appliances
Maytag Appliances We Repair Around Denver
Maytag is part of Whirlpool Corporation, and we service the full range of its household appliances.
Maytag Refrigerator Repair
Maytag refrigerators commonly develop warm fresh food sections, frost on the evaporator, noisy fans or ice makers that slow down or quit. We repair defrost systems, fans, thermistors, control boards, water valves and ice makers so food stays cold and ice keeps coming.
Refrigerator RepairMaytag Washer Repair
Washers that will not drain, will not spin, leak or stop mid-cycle are common complaints with Maytag top-load and front-load models alike. We work on drain pumps, lid and door locks, drive components, shifters, suspension parts and controls.
Washer RepairMaytag Dryer Repair
Maytag dryers often run but stop heating, take two cycles to dry, or make thumping and squealing sounds. We replace heating elements, thermal fuses, gas valve coils, igniters, belts, rollers and moisture sensors, and we check airflow along the way.
Dryer RepairMaytag Dishwasher Repair
Standing water, poor cleaning, leaks and fill problems are typical for any dishwasher, and Maytag models are no exception. We repair drain and circulation pumps, fill valves, float switches, door latches and control boards.
Dishwasher RepairMaytag Oven Repair
Ovens that will not heat, heat unevenly or run hotter than the setting usually point to a failed element, igniter or temperature sensor. We test and replace those parts along with door switches, locks and controls.
Oven RepairMaytag Range & Stove Repair
Maytag ranges and stoves commonly show burners that click without lighting, weak flames or electric coils and surface elements that stay cold. We repair igniters, spark modules, burner valves, infinite switches and surface elements on gas and electric models.
Range & Stove RepairMaytag Microwave Repair
A microwave that runs but does not heat, sparks, or has a dead keypad is a common frustration. We service over-the-range Maytag microwaves, including door switches, fans, lights and control issues, and we explain plainly when a repair makes sense.
Microwave Repair
Error Codes
Maytag Error Codes by Appliance
What common Maytag codes mean — taken from Maytag's own support pages — what you can safely try first, and when it's time to call us.
Maytag Dishwasher Error Codes
| Code | What it means | Try first | DIY or pro? |
|---|---|---|---|
| F9E1Try it yourself | Long drain — the dishwasher isn't draining.Clean the filter, check the drain hose for kinks or clogs, clear the disposer (and remove its knockout plug on a new install) and the air gap. | Clean the filter, check the drain hose for kinks or clogs, clear the disposer (and remove its knockout plug on a new install) and the air gap. | Try it yourself |
| F9E2Call a pro | Drain motor error.Check the disposer and drain for clogs and straighten the drain hose. Cycle power; if it returns, call for service. | Check the disposer and drain for clogs and straighten the drain hose. Cycle power; if it returns, call for service. | Call a pro |
| F8E4Call a pro | Water in the base (the float switch tripped) — often a leak or excessive suds.Turn off the water supply. Check connections and the drip tray, avoid dish soap. If the dishwasher was professionally installed, call for service. | Turn off the water supply. Check connections and the drip tray, avoid dish soap. If the dishwasher was professionally installed, call for service. | Call a pro |
| F8E5Call a pro | Fill valve stuck open.Turn off the water to the dishwasher, press Cancel once and keep the door closed — then call for service. | Turn off the water to the dishwasher, press Cancel once and keep the door closed — then call for service. | Call a pro |
| F8E2Call a pro | Fill valve electrical error.Check the inlet valve connection for leaks, cycle power; if it returns, call for service. | Check the inlet valve connection for leaks, cycle power; if it returns, call for service. | Call a pro |
| H2OTry it yourself | Not detecting water.Make sure the water supply is on and the supply hose isn't kinked, then press Start. | Make sure the water supply is on and the supply hose isn't kinked, then press Start. | Try it yourself |
| F6E3Try it yourself | Excessive suds.Scoop out the suds, add 2–3 tablespoons of vegetable oil and run a cycle with no detergent, then a cycle with detergent and no dishes. | Scoop out the suds, add 2–3 tablespoons of vegetable oil and run a cycle with no detergent, then a cycle with detergent and no dishes. | Try it yourself |
| F6E4Try it yourself | Water float switch.Level the dishwasher and cycle power. | Level the dishwasher and cycle power. | Try it yourself |
| F4E2, F4E3Call a pro | Heating system error.Disconnect power for 30 seconds. If the code returns, call for service. | Disconnect power for 30 seconds. If the code returns, call for service. | Call a pro |
| F7E2Call a pro | Wash motor error.Cycle power; if the code returns, call for service. | Cycle power; if the code returns, call for service. | Call a pro |
| FAE4 / F10E4, FAE5 / F10E5Call a pro | Diverter valve error (E4) or diverter leak (E5).Check for leaks under the dishwasher, cycle power or press Cancel twice. If it returns, call for service. | Check for leaks under the dishwasher, cycle power or press Cancel twice. If it returns, call for service. | Call a pro |
| F1E1, F1E2, F2E1, F2E2, F3E2, F6E1Call a pro | Control, keypad, communication or sensor (thermistor/OWI) errors.Disconnect power for 30 seconds. If the code returns, call for service. | Disconnect power for 30 seconds. If the code returns, call for service. | Call a pro |
Source: Maytag Product Help — dishwasher error codes (one article per code). Codes vary by model — check your owner's manual.
Maytag Dryer Error Codes
| Code | What it means | Try first | DIY or pro? |
|---|---|---|---|
| F4E3Try it yourself | Restricted airflow — the lint screen or vent is clogged, or the vent is crushed, kinked or has too many turns.Clean the lint screen, check the vent run and outside hood. If it persists, have the whole vent cleaned. | Clean the lint screen, check the vent run and outside hood. If it persists, have the whole vent cleaned. | Try it yourself |
| F4E4Try it yourself | Low or no line voltage — the heater can't turn on.Check both breakers (electric dryers need 240 V on a separate 30-amp circuit) and the power cord; call an electrician if needed. | Check both breakers (electric dryers need 240 V on a separate 30-amp circuit) and the power cord; call an electrician if needed. | Try it yourself |
| F4E1Call a pro | Heater system — the heater or heater relays.Turn off the breaker for 1 minute, restart on Timed Dry. If it returns, call for service. | Turn off the breaker for 1 minute, restart on Timed Dry. If it returns, call for service. | Call a pro |
| F3E2, F3E5Try it yourself | Moisture sensor — five loads in a row dried without sensor data.Level the dryer and dry fuller loads on an Automatic cycle. Power cycle if it continues. | Level the dryer and dry fuller loads on an Automatic cycle. Power cycle if it continues. | Try it yourself |
| F3E1, F3E3Call a pro | Exhaust or inlet thermistor.Power cycle for 1 minute and run a Timed Dry cycle. If it returns, call for service. | Power cycle for 1 minute and run a Timed Dry cycle. If it returns, call for service. | Call a pro |
| F7E1Call a pro | Motor system — motor, control or wiring.Power cycle for 1 minute. If it returns, call for service. | Power cycle for 1 minute. If it returns, call for service. | Call a pro |
| F1E1, F1E3, F1E4, F1E5, F2E1, F2E2, F6E1Call a pro | Control unit, keypad or communication error.Power cycle at the breaker and run a Timed Dry cycle. If the code comes back, call for service. | Power cycle at the breaker and run a Timed Dry cycle. If the code comes back, call for service. | Call a pro |
Source: Maytag Product Help — dryer error codes (one article per code). Codes vary by model — check your owner's manual.
Maytag Washer Error Codes
Note: Maytag and Whirlpool are the same company and share most front-load codes..
| Code | What it means | Try first | DIY or pro? |
|---|---|---|---|
| F9 E1Try it yourself | Drain is taking longer than expected.Check the drain hose and standpipe, and use HE detergent. | Check the drain hose and standpipe, and use HE detergent. | Try it yourself |
| F5 E2Try it yourself | The door isn't locking properly.Clear anything blocking the door and close it completely. | Clear anything blocking the door and close it completely. | Try it yourself |
| Sud, SdTry it yourself | Too many suds.Use the right amount of HE detergent. | Use the right amount of HE detergent. | Try it yourself |
| IntTry it yourself | The cycle was paused or canceled — the washer may take 20–30 minutes to stop and drain.Wait, then press Pause/Cancel twice and Power once to clear it. | Wait, then press Pause/Cancel twice and Power once to clear it. | Try it yourself |
| F7 E1Call a pro | Motor speed sensing error.Make sure the washer isn't overloaded. A repeat code needs a technician. | Make sure the washer isn't overloaded. A repeat code needs a technician. | Call a pro |
Source: Maytag Product Help — error codes in front load washers. Codes vary by model — check your owner's manual.
Common Problems
Maytag Problems That Usually Have a Clear Cause
Most Maytag breakdowns follow a recognizable pattern, which helps your technician narrow things down quickly.
Washer not draining or not spinning
- Likely causes
- Clogged drain pump or pump filter, kinked drain hose, worn lid or door lock, or a failing drive belt or coupler
- What we check
- Pump and filter, hose routing, lock operation, drive parts and any washer fault codes stored in the control
Dryer not heating or taking too long
- Likely causes
- Restricted vent (often shown as F4E3), blown thermal fuse, failed heating element or gas igniter, or low line voltage (F4E4)
- What we check
- Lint screen and vent run, both breakers and the 240-volt supply, heater circuit, fuses and gas valve parts
Dishwasher leaving water behind
- Likely causes
- Clogged filter, blocked drain hose or a weak drain pump, often logged as F9E1 for a long drain or F9E2 for the drain motor
- What we check
- Filter, sump, drain path, disposal connection and pump performance
Dishwasher leak or water in the base
- Likely causes
- Worn door gasket, loose hose clamp, leaking pump seal, or a fill valve stuck open (F8E4 and F8E5)
- What we check
- Base pan, float switch, seals, fill valve and every hose connection
Refrigerator not cooling
- Likely causes
- Frosted evaporator from a defrost failure, a stalled fan, dusty condenser coils or a faulty control
- What we check
- Defrost heater and sensor, fans, coil condition, temperatures and the main control
Gas range or oven not lighting
- Likely causes
- Weak or failed igniter, clogged burner ports, or a supply setup that does not suit the altitude
- What we check
- Igniter draw, burner condition, flame quality and the gas setup for Colorado elevation
Before You Call
Finding the Model and Serial Number on Your Maytag
Having the model and serial number ready when you call helps us prepare the right parts, and the tag is usually in one of these spots.
Refrigerator
Usually on a label inside the fresh food compartment, along a side wall or near the ceiling light
Washer
Usually under the lid or on the back of the console for top-load models, and around the door opening for front-load models
Dryer
Usually inside the door opening on the frame, or on the back panel
Dishwasher
Usually on the edge of the inner door or along the side of the tub opening, visible when the door is open
Range and oven
Usually behind the storage drawer or on the frame around the oven door opening
Google Reviews
What Maytag Owners Say
5.0Every review on Google is five stars.
“Excellent service! Nick is a very knowledgeable and skillful appliance repair master. He was on time, well-prepared, clean, and respectful of my home. He was able to diagnose the problem with the Maytag front-load washing machine within minutes. Nick clearly explained the repair and cost before starting the repair. The machine was working normally within 15 minutes after his arrival. I am particularly impressed by his honesty! Instead of trying to sell me a replacement of the computer chip that created the problem with the washer he simply reset it and it has been working fine. In addition he patiently explained and showed me how to reset it myself in the unlikely event it happens again. It has been a month since he repaired it and the machine has been working without any problems. My appliance is working perfectly again, and the price was fair. I highly recommend Nick to anyone looking for reliable appliance repair! I saved his contact info and will hire him again whenever I need my appliances serviced or repaired. Thank you, Nick!”
Alex S.October 2026 · Google
Care Tips
Maytag Care Tips for Colorado Households
Keep the dryer vent clear
A crushed, long or lint-packed vent is a common reason Maytag dryers show F4E3 and run long cycles. Clean the lint screen every load and have the full vent cleaned periodically, especially if drying times start to creep up.
Stay ahead of mineral scale
Denver-area water ranges from soft to moderately hard, and scale commonly builds up in dishwashers, washers and ice makers. Run cleaning cycles with a proper cleaner and rinse the dishwasher filter regularly.
Give the refrigerator room to breathe
Colorado's dry air carries plenty of dust, and dusty condenser coils make a refrigerator work harder. Vacuuming the coils and keeping vents inside the cabinet unblocked helps it hold temperature.
Set gas appliances up for altitude
Homes here sit roughly a mile high, so gas ranges and dryers need correct setup for the elevation. Yellow, lazy or noisy flames are a good reason to have the appliance checked.
Membership
PointLine Care Club
One service call is $85. For $99 a year, every service call is free.
- Free service calls all year — no $85 fee
- 1 free maintenance visit a year
- 10% off labor on every repair
$99/ year
One household · renews yearly · cancel anytime before renewal
Property manager or landlord? See our Property Care Club →
Repair or Replace?
Should You Repair Your Maytag or Replace It?
For many Maytag appliances, repair is the sensible choice. A drain pump, igniter, heating element or door lock is usually a straightforward fix, and the rest of the machine often has plenty of life left. If the cabinet, drum or tub is in good shape and the problem is a single part, fixing it typically costs far less than starting over.
Replacement starts to make more sense when an older unit needs a major component such as a sealed system, a transmission or a main control, or when several problems show up at once. Your technician will lay out the repair cost, the condition of the appliance and the honest tradeoffs, then leave the decision to you.
Everyday Brands
Other Popular Brands We Repair
- Whirlpool Repair
- GE Repair
- LG Repair
- Samsung Repair
- KitchenAid Repair
- Frigidaire Repair
- Amana Repair
- Kenmore Repair
- Electrolux Repair
- Haier Repair
Service Areas
Maytag Repair Near You
We repair Maytag appliances in all 21 communities we serve across the Denver Metro Area and Boulder County.
- Maytag Repair in Arvada
- Maytag Repair in Aurora
- Maytag Repair in Boulder
- Maytag Repair in Brighton
- Maytag Repair in Broomfield
- Maytag Repair in Commerce City
- Maytag Repair in Denver
- Maytag Repair in Englewood
- Maytag Repair in Erie
- Maytag Repair in Golden
- Maytag Repair in Highlands Ranch
- Maytag Repair in Lafayette
- Maytag Repair in Lakewood
- Maytag Repair in Littleton
- Maytag Repair in Longmont
- Maytag Repair in Louisville
- Maytag Repair in Northglenn
- Maytag Repair in Superior
- Maytag Repair in Thornton
- Maytag Repair in Westminster
- Maytag Repair in Wheat Ridge
FAQ
Maytag Repair Questions, Answered
Questions Maytag owners ask us.
Do you repair Maytag washers that will not drain or spin?
Yes, Maytag washer repair is a big part of what we do across the Denver area. Drain and spin problems often come from a clogged pump or filter, a worn lid or door lock, or drive parts. Your technician tests each one so the actual cause gets fixed.
What does it cost to have a technician come out?
The diagnostic visit is $85, and it is credited toward the repair if you go ahead. After the diagnosis you receive a firm quote before any work starts.
Do you use genuine Maytag parts?
Yes, we install genuine OEM parts. They are made to fit and perform as the appliance was designed, which helps the repair last.
What if the same problem comes back after the repair?
Every repair carries a 90-day parts and labor warranty. If the repaired part fails within that window, call us at (720) 285-3573 and we will make it right.
My Maytag dryer shows F4E3, or my dishwasher shows F9E1. What do those mean?
F4E3 points to restricted dryer airflow, and F9E1 means the dishwasher took too long to drain. For the dryer, clean the lint screen and check the vent for crushing or lint buildup. For the dishwasher, rinse the filter and look for a kinked drain hose; if the code returns, it is time for a technician.
Is my older Maytag worth fixing?
Often it is, especially when the problem is a single part and the rest of the appliance is in good condition. When a major component fails on an aging unit, replacement may be the better value, and your technician will explain both options plainly.
Which areas does PointLine serve?
We serve 21 cities across the Denver Metro Area and Boulder County from our office in Superior. Call (720) 285-3573 and we will confirm your address and find a visit time that works.
Get Your Maytag Back to Everyday Work
Call PointLine at (720) 285-3573 to schedule a $85 diagnostic, credited toward the repair. We use genuine OEM parts, back the work for 90 days, and accept cash, major credit cards, Venmo, Apple Pay and checks. Ask about the $99 yearly Care Club for free service calls, an annual maintenance visit and 10% off labor.
PointLine Appliance Repair is an independent repair company, not affiliated with Maytag.