Local • Family-Owned
Maytag Repair in Boulder, CO
Washers, dryers, fridges, dishwashers and cooking appliances diagnosed at your home by an independent family company just down US-36, with a firm quote before work.
We repair every Maytag appliance
- $85 DiagnosticCredited toward your repair
- 90-Day WarrantyParts & labor
- Open 24/7Same-day service often available
- Local & Family-OwnedBased in Superior
Maytag Repair • Boulder
Plainspoken Help for the Maytag You Count On
When a hard-working Maytag finally quits mid-task, Boulder households turn to PointLine for Maytag repair, and we head out from our office at 2600 S Rock Creek Pkwy #103 in Superior. We are an independent, family-owned company, insured, and close enough that the trip to your door is a quick run up US-36. Maytag shows up all over town, from laundry closets in older houses to the kitchens of rentals near campus, usually as the appliance nobody thinks about until it stops. When that happens, you want someone who will find the real fault, explain it in plain terms and give you a price before touching anything.
Maytag appliances share a lot of engineering with other brands in the same family, which is useful because parts are widely available, but it also means one symptom can come from several different places. A washer that won't spin might have a worn lid lock, a stretched belt, a failing motor control or simply a clogged drain, and swapping parts until something works gets expensive quickly. Your visit starts with a $85 diagnostic that is credited toward the repair, and you get a firm quote before any work begins. Every repair we complete is backed by a 90-day parts and labor warranty, and we install genuine OEM parts matched to your unit.
Maytag Appliances
Every Maytag in the House, From Laundry Room to Kitchen
These are the Maytag appliances we repair, along with the usual trouble spots and what your technician tests on each.
Maytag Refrigerator
Warm fresh-food sections, frost on the freezer back wall and ice makers that stop producing are the complaints that bring most Maytag refrigerators to our attention. We check condenser coils and fans, defrost heaters and thermostats, door gaskets, temperature sensors and the water valve before deciding which part has actually failed.
Maytag refrigerator repair in BoulderMaytag Washer
Maytag washers tend to give up in recognizable ways: they won't drain, won't spin, leak at the front or bang hard during the final spin. We test the drain pump, lid or door lock, suspension, shocks, bearings and motor control, and we look at hoses and the door boot for wear or trapped debris.
Maytag washer repair in BoulderMaytag Dryer
A dryer that tumbles without heat, takes two cycles to dry towels or shuts off early usually points to a heating circuit, a safety fuse or restricted airflow. On electric models we test the element, thermal fuse and thermostats; on gas models we check the igniter, flame sensor and gas valve coils, and on both we look at the vent run.
Maytag dryer repair in BoulderMaytag Dishwasher
Standing water, cloudy dishes, leaks under the door and cycles that never finish are the common Maytag dishwasher frustrations. We inspect the filter, drain pump, wash motor, inlet valve, door latch and spray arms, and we read any stored fault information before quoting.
Maytag dishwasher repair in BoulderMaytag Oven
Ovens that heat slowly, run hot or cold, or refuse to turn on usually trace back to an element, igniter, temperature sensor or control. We verify actual cavity temperatures, test the bake and broil circuits and check door locks on self-cleaning models that won't release.
Maytag oven repair in BoulderMaytag Range & Stove
On Maytag ranges, a burner that clicks without lighting, a radiant zone that stays dark or a knob that won't hold its setting are the faults we track down most. We test spark modules, igniters, infinite switches, surface elements and wiring, and we make sure gas burners are adjusted correctly for the house.
Maytag range & stove repair in BoulderMaytag Microwave
A microwave that runs but leaves food cold, a dead keypad or an over-the-range vent fan that won't come on all have different causes. We check door switches, the high-voltage components, the control board and touchpad, and on mounted units the fan, lights and mounting before giving you a price.
Maytag microwave repair in Boulder
Error Codes
Maytag Fault Codes, Straight From the Source
The code tables below come from Maytag's own support pages and are organized by appliance type, so you can match what your display shows to its meaning. Codes marked as safe to try yourself usually call for a simple step like a reset, a cleaned filter or a closed door, while codes marked for a pro point to parts or wiring that need testing with proper tools.
| Code | What it means | Try first | DIY or pro? |
|---|---|---|---|
| F9E1Try it yourself | Long drain — the dishwasher isn't draining.Clean the filter, check the drain hose for kinks or clogs, clear the disposer (and remove its knockout plug on a new install) and the air gap. | Clean the filter, check the drain hose for kinks or clogs, clear the disposer (and remove its knockout plug on a new install) and the air gap. | Try it yourself |
| F9E2Call a pro | Drain motor error.Check the disposer and drain for clogs and straighten the drain hose. Cycle power; if it returns, call for service. | Check the disposer and drain for clogs and straighten the drain hose. Cycle power; if it returns, call for service. | Call a pro |
| F8E4Call a pro | Water in the base (the float switch tripped) — often a leak or excessive suds.Turn off the water supply. Check connections and the drip tray, avoid dish soap. If the dishwasher was professionally installed, call for service. | Turn off the water supply. Check connections and the drip tray, avoid dish soap. If the dishwasher was professionally installed, call for service. | Call a pro |
| F8E5Call a pro | Fill valve stuck open.Turn off the water to the dishwasher, press Cancel once and keep the door closed — then call for service. | Turn off the water to the dishwasher, press Cancel once and keep the door closed — then call for service. | Call a pro |
| F8E2Call a pro | Fill valve electrical error.Check the inlet valve connection for leaks, cycle power; if it returns, call for service. | Check the inlet valve connection for leaks, cycle power; if it returns, call for service. | Call a pro |
| H2OTry it yourself | Not detecting water.Make sure the water supply is on and the supply hose isn't kinked, then press Start. | Make sure the water supply is on and the supply hose isn't kinked, then press Start. | Try it yourself |
| F6E3Try it yourself | Excessive suds.Scoop out the suds, add 2–3 tablespoons of vegetable oil and run a cycle with no detergent, then a cycle with detergent and no dishes. | Scoop out the suds, add 2–3 tablespoons of vegetable oil and run a cycle with no detergent, then a cycle with detergent and no dishes. | Try it yourself |
| F6E4Try it yourself | Water float switch.Level the dishwasher and cycle power. | Level the dishwasher and cycle power. | Try it yourself |
| F4E2, F4E3Call a pro | Heating system error.Disconnect power for 30 seconds. If the code returns, call for service. | Disconnect power for 30 seconds. If the code returns, call for service. | Call a pro |
| F7E2Call a pro | Wash motor error.Cycle power; if the code returns, call for service. | Cycle power; if the code returns, call for service. | Call a pro |
| FAE4 / F10E4, FAE5 / F10E5Call a pro | Diverter valve error (E4) or diverter leak (E5).Check for leaks under the dishwasher, cycle power or press Cancel twice. If it returns, call for service. | Check for leaks under the dishwasher, cycle power or press Cancel twice. If it returns, call for service. | Call a pro |
| F1E1, F1E2, F2E1, F2E2, F3E2, F6E1Call a pro | Control, keypad, communication or sensor (thermistor/OWI) errors.Disconnect power for 30 seconds. If the code returns, call for service. | Disconnect power for 30 seconds. If the code returns, call for service. | Call a pro |
Source: Maytag Product Help — dishwasher error codes (one article per code). Codes vary by model — check your owner's manual.
| Code | What it means | Try first | DIY or pro? |
|---|---|---|---|
| F4E3Try it yourself | Restricted airflow — the lint screen or vent is clogged, or the vent is crushed, kinked or has too many turns.Clean the lint screen, check the vent run and outside hood. If it persists, have the whole vent cleaned. | Clean the lint screen, check the vent run and outside hood. If it persists, have the whole vent cleaned. | Try it yourself |
| F4E4Try it yourself | Low or no line voltage — the heater can't turn on.Check both breakers (electric dryers need 240 V on a separate 30-amp circuit) and the power cord; call an electrician if needed. | Check both breakers (electric dryers need 240 V on a separate 30-amp circuit) and the power cord; call an electrician if needed. | Try it yourself |
| F4E1Call a pro | Heater system — the heater or heater relays.Turn off the breaker for 1 minute, restart on Timed Dry. If it returns, call for service. | Turn off the breaker for 1 minute, restart on Timed Dry. If it returns, call for service. | Call a pro |
| F3E2, F3E5Try it yourself | Moisture sensor — five loads in a row dried without sensor data.Level the dryer and dry fuller loads on an Automatic cycle. Power cycle if it continues. | Level the dryer and dry fuller loads on an Automatic cycle. Power cycle if it continues. | Try it yourself |
| F3E1, F3E3Call a pro | Exhaust or inlet thermistor.Power cycle for 1 minute and run a Timed Dry cycle. If it returns, call for service. | Power cycle for 1 minute and run a Timed Dry cycle. If it returns, call for service. | Call a pro |
| F7E1Call a pro | Motor system — motor, control or wiring.Power cycle for 1 minute. If it returns, call for service. | Power cycle for 1 minute. If it returns, call for service. | Call a pro |
| F1E1, F1E3, F1E4, F1E5, F2E1, F2E2, F6E1Call a pro | Control unit, keypad or communication error.Power cycle at the breaker and run a Timed Dry cycle. If the code comes back, call for service. | Power cycle at the breaker and run a Timed Dry cycle. If the code comes back, call for service. | Call a pro |
Source: Maytag Product Help — dryer error codes (one article per code). Codes vary by model — check your owner's manual.
| Code | What it means | Try first | DIY or pro? |
|---|---|---|---|
| F9 E1Try it yourself | Drain is taking longer than expected.Check the drain hose and standpipe, and use HE detergent. | Check the drain hose and standpipe, and use HE detergent. | Try it yourself |
| F5 E2Try it yourself | The door isn't locking properly.Clear anything blocking the door and close it completely. | Clear anything blocking the door and close it completely. | Try it yourself |
| Sud, SdTry it yourself | Too many suds.Use the right amount of HE detergent. | Use the right amount of HE detergent. | Try it yourself |
| IntTry it yourself | The cycle was paused or canceled — the washer may take 20–30 minutes to stop and drain.Wait, then press Pause/Cancel twice and Power once to clear it. | Wait, then press Pause/Cancel twice and Power once to clear it. | Try it yourself |
| F7 E1Call a pro | Motor speed sensing error.Make sure the washer isn't overloaded. A repeat code needs a technician. | Make sure the washer isn't overloaded. A repeat code needs a technician. | Call a pro |
Source: Maytag Product Help — error codes in front load washers. Codes vary by model — check your owner's manual.
Common Problems
Familiar Maytag Symptoms and What Sits Behind Them
Your technician tests your unit to pinpoint the real cause before quoting any repair, so the common patterns we describe are only a starting point.
Washer stops with water in the tub
- Likely causes
- Clogged drain pump filter, a sock or coin in the pump, kinked drain hose, failed pump motor
- What we check
- Pump and filter condition, hose routing, pump voltage and the control's drain signal
Dryer runs but stays cool
- Likely causes
- Blown thermal fuse, open heating element or burned-out igniter, restricted vent causing safety shutoffs
- What we check
- Continuity on fuse, element and thermostats, gas valve coils, and airflow at the outside hood
Refrigerator warm while freezer seems fine
- Likely causes
- Frost blocking the evaporator, failed defrost heater or thermostat, weak evaporator fan, damper stuck closed
- What we check
- Frost pattern on the coil, defrost components, fan operation and air passage between compartments
Dishwasher leaves dishes dirty or gritty
- Likely causes
- Clogged filter, blocked spray arm holes, weak wash motor, inlet valve not letting in enough water
- What we check
- Filter and spray arms, fill level, wash motor performance and water temperature at the start of the cycle
Oven temperature drifts from the setting
- Likely causes
- Weak igniter on gas models, failing bake element, temperature sensor out of range, control issue
- What we check
- Measured cavity temperature, igniter draw, element resistance and sensor readings against specification
Loud banging or shaking during spin
- Likely causes
- Unbalanced load, worn shocks or suspension springs, failing tub bearings, washer not level
- What we check
- Suspension and dampers, bearing noise by hand rotation, leveling legs and the floor beneath the machine
Boulder Homes
How Local Homes Shape the Life of a Maytag
A few real features of this city bear directly on how Maytag appliances are installed, used and repaired here.
Older houses, newer appliances
Mapleton Hill is a designated historic district full of Victorian and Craftsman houses, many built before 1910, and plenty of other neighborhoods have homes that were updated rather than torn down. A full-size Maytag washer or dryer in one of these houses may sit in a converted closet, a basement corner or a tight alcove that was never planned for laundry. That affects vent length, drain height and how easily a machine can be pulled out for service. We look at the installation as part of the diagnosis, because a cramped setup can cause the very fault you called about.
Gas appliances above 5,000 feet
Boulder sits above 5,000 feet, and the thinner air at that height affects how gas burns in a Maytag range, oven or dryer. A burner that lifts its flame, a dryer that takes longer to ignite or an oven that heats unevenly can sometimes be a setup question rather than a broken part. When we work on gas appliances, we check flame quality and burner adjustment so the repair holds up in local conditions.
Rentals, students and mountain water
University Hill sits next to CU and is a center of off-campus rental life, where Maytag washers, dryers and dishwashers often serve a rotating cast of tenants. Machines in shared homes tend to see heavy loads, overstuffed drums and filters that nobody cleans, so we explain the fault clearly for both owners and tenants. The city's water comes from Arapahoe Glacier and Boulder Creek, and every dishwasher fill and ice maker cycle depends on the supply valve and line that carry it into the appliance, which is why we check those first when water stops flowing.
Know Your Maytag
Know-How That Speeds Up a Maytag Repair
A few working habits make the difference between a quick, correct fix and a second trip.
Start with the tag
The model and serial number tell us exactly which version of your Maytag we are dealing with, since appliances that look alike can carry different boards, motors and pumps. On washers and dryers the tag is often inside the door or lid; on refrigerators it is usually on an inside wall; on dishwashers it sits along the edge of the tub or door. A photo of it when you book lets us arrive with the right parts more often.
Connected features and control boards
Some newer Maytag appliances offer app connectivity and electronic controls that monitor sensors, motors and valves. A board can fail on its own, but it can also report a problem that actually lives in a sensor or harness, so we test inputs and outputs before blaming the electronics. That keeps you from paying for an expensive board that was only delivering bad news.
When a code describes a process
Some Maytag codes name a specific part, while others simply report that a fill, drain or heat-up took too long. A slow-drain code might mean a worn pump, but it can just as easily mean a clogged filter or a hose pinched behind the machine. We treat those codes as a starting point and trace the whole system before quoting.
Genuine parts, matched carefully
We install genuine OEM parts selected by your model and serial number, not by appearance. Because Maytag shares engineering with other appliances in its corporate family, many parts are readily available, and that often makes repair a practical choice. If a part has to be ordered, we say so right away and book your return visit for as soon as it comes in.
Repair or Replace?
Is Your Maytag Worth Fixing?
The typical lifespans shown beside this section offer a rough sense of how long each type of appliance tends to serve, but your own Maytag's age is only one piece of the decision. A washer with a failed pump or a refrigerator with a bad defrost heater usually has plenty of life left once that single part is replaced. We give you a firm quote after the diagnosis, so you can compare the repair cost with the price of a new unit, delivery and installation before committing to anything. If a repair doesn't make sense, we will say so plainly.
Replacement starts to look smarter when an aging appliance needs a costly core component, when it has been through several repairs in a short stretch, or when parts for it are getting hard to find. Energy use belongs in the math too, especially for an older refrigerator or freezer that runs around the clock. On the other hand, keeping a sound machine running avoids the hassle of hauling a heavy appliance out of a tight laundry closet or a historic kitchen. Either way, our job is to give you the facts so the choice is yours.
Typical lifespan by appliance
| Refrigerator | ~13 yrs |
|---|---|
| Washer | ~10 yrs |
| Dryer | ~13 yrs |
| Dishwasher | ~9 yrs |
| Oven | ~13–15 yrs |
| Range & Stove | ~13–15 yrs |
| Microwave | ~9 yrs |
Source: NAHB study of home component life. Any brand; real life varies with use and care.
Google Reviews
What Our Customers Say
5.0Every review on Google is five stars.
“Excellent work, executed with speed and caution. I had an issue with my fridge/freezer and was concerned I’d need to toss my food. Thankfully PointLine was able to respond right away. I’d use them again and would recommend them as well.”
Jay H.May 2026 · Google “My GE refrigerator stopped cooling shortly after we moved to Superior. We wanted to support a local company, so we called PointLine Appliance Repair. Nick came out the same day, fixed the fridge on the spot, and the price was very reasonable. Super friendly, professional, and easy to work with. We’ll definitely call them again if we ever need another appliance repaired. Highly recommend!”
Alyssa M.July 2026 · Google “Nick was great. Quickly narrowed down our likely washer problem and got the part ordered with deposit. Quick install and had washer working within few hours once part arrived. Great communication throughout. Would definitely use again!”
Nathan H.August 2026 · Google
Membership
PointLine Care Club
One service call is $85. For $99 a year, every service call is free.
- Free service calls all year — no $85 fee
- 1 free maintenance visit a year
- 10% off labor on every repair
$99/ year
One household · renews yearly · cancel anytime before renewal
Property manager or landlord? See our Property Care Club →
Boulder Service Area
Maytag Repair Across Boulder
ZIP codes 80301, 80302, 80303, 80304, 80305, 80310 and the neighboring communities we serve every week.
Managing rentals? See the Property Care Club.
Other brands in Boulder
- Bosch repair in Boulder
- Frigidaire repair in Boulder
- GE repair in Boulder
- Kenmore repair in Boulder
- KitchenAid repair in Boulder
- LG repair in Boulder
- Miele repair in Boulder
- Samsung repair in Boulder
- Sub-Zero repair in Boulder
- Thermador repair in Boulder
- Viking repair in Boulder
- Whirlpool repair in Boulder
- Wolf repair in Boulder
- JennAir repair in Boulder
FAQ
Maytag Questions From Local Homes
Straight answers for Maytag owners in Boulder.
Are you connected to Maytag?
No, PointLine is an independent, family-owned repair company and has no affiliation with Maytag. We repair Maytag appliances using genuine OEM parts and stand behind our work with a 90-day parts and labor warranty.
My Maytag is showing a code. Can I fix it myself?
Sometimes, and the code tables on this page show which codes usually clear with a simple step. Give the suggested fix a single try, and if the code comes back, book a visit and share the code with us so we can come prepared.
Can you repair Maytag appliances with app connectivity or electronic controls?
Yes, we diagnose and repair Maytag models with electronic controls and connected features. We test the sensors and parts the board relies on, so you only replace the board if it has truly failed.
Do you use genuine parts on Maytag repairs?
Yes, the parts we install are genuine OEM parts matched to your model and serial number. When a part needs ordering, we tell you before we schedule the follow-up visit.
How quickly can a technician get to you?
We can often offer same-day service, although we can't guarantee it. Booking early in the day and sharing your model number helps us fit you in.
Which ZIP codes do you cover in Boulder?
Our service area covers 80301, 80302, 80303, 80304, 80305 and 80310. Our Superior office also covers nearby Louisville, Lafayette, Broomfield, Erie and Longmont.
What does the visit cost?
The diagnostic visit is $85, and that amount is credited toward the repair if you go ahead. You get a firm quote before any work begins, and households can join the PointLine Care Club for $99 a year.
Which Maytag needs attention at your house?
Book online or call or text (720) 285-3573, and we will start with a $85 diagnostic credited toward your repair.
PointLine Appliance Repair is an independent repair company, not affiliated with Maytag.