Local • Family-Owned
Maytag Repair in Arvada, CO
An independent family company from nearby Superior tests your Maytag at home, explains what failed and quotes a firm price before any work starts.
We repair every Maytag appliance
- $85 DiagnosticCredited toward your repair
- 90-Day WarrantyParts & labor
- Open 24/7Same-day service often available
- Local & Family-OwnedBased in Superior
Maytag Repair • Arvada
A Family Repair Shop for the Maytag Machines You Lean On
Arvada families who need Maytag repair can book with PointLine without a trip across the metro, since our family-owned office sits at 2600 S Rock Creek Pkwy #103 in Superior. We are an independent company, not part of Maytag, and that keeps our attention on your machine instead of a sales goal. A visit begins with a $85 diagnostic, credited toward the repair if you go ahead, and you get a firm quote before a single screw comes out. Every part we install is genuine OEM, and the work carries a 90-day parts and labor warranty.
Maytag machines turn up in all kinds of homes around town, from mid-century ranches with a washer and dryer tucked into the basement to remodeled kitchens with a stainless range and an over-the-range microwave. Because these appliances run on control boards, sensors and shared component designs, one symptom can trace back to several different parts. A dryer that won't heat might have a failed element, an open fuse or a choked vent, and swapping parts by guesswork gets expensive fast. Testing first, with a meter and a real cycle, is how we make sure the repair you pay for is the one your Maytag actually needs.
Maytag Appliances
Seven Maytag Appliances, One Careful Process
Here is each Maytag appliance we repair, along with the faults that tend to show up and what your technician tests before naming a cause.
Maytag Refrigerator
Maytag refrigerators usually come to us running warm, frosting over, leaking water or making little ice. We check condenser coils and fans, read the frost pattern on the evaporator, test the defrost circuit and confirm the water valve and ice maker are getting what they need.
Maytag refrigerator repair in ArvadaMaytag Washer
Washers that won't drain, won't spin, leak or stop mid-cycle are the most common calls for this machine. We inspect the pump and its filter, test the lid or door lock, look over hoses and seals and watch the motor and drive through a test cycle.
Maytag washer repair in ArvadaMaytag Dryer
Dryers that stay cool, run forever, squeal or shut off early usually have a problem in the heating circuit, the drive parts or the vent. We measure each heating component, check the belt, rollers and idler, and test airflow at the outside hood so a blocked duct doesn't ruin a new part.
Maytag dryer repair in ArvadaMaytag Dishwasher
Cloudy glasses, standing water, leaks and dishes that come out wet point to a short list of suspects. We pull and inspect the filter, check spray arms and the drain path to the sink, test the pump and heating element and measure the fill.
Maytag dishwasher repair in ArvadaMaytag Oven
A Maytag oven that heats slowly, runs hot or cold or won't heat at all needs measurement more than guesswork. We test the bake and broil elements or gas igniter, compare the temperature sensor against a test thermometer and check the door gasket and control signals.
Maytag oven repair in ArvadaMaytag Range & Stove
On the cooktop side, we see burners that click without lighting, elements that stay cold and controls that stick on high. We clean and seat burner caps, test spark switches and modules, measure element resistance and inspect terminals and wiring for heat damage.
Maytag range & stove repair in ArvadaMaytag Microwave
Microwaves that hum without heating, show a blank display or spark inside hold high-voltage parts that need careful handling. We safely discharge the circuit, then test the door switches, fuse, high-voltage components and control board, and on over-the-range models we check the fan and light as well.
Maytag microwave repair in Arvada
Error Codes
Maytag Error Codes, Explained by the Maker
The tables below list error codes as Maytag publishes them on its own support pages, grouped by appliance so you can find your machine and read what its display is reporting. Codes marked as safe to try yourself usually involve a simple step like clearing a filter or resetting power, while codes marked for a pro point to parts and wiring that call for a technician with the right tools.
| Code | What it means | Try first | DIY or pro? |
|---|---|---|---|
| F9E1Try it yourself | Long drain — the dishwasher isn't draining.Clean the filter, check the drain hose for kinks or clogs, clear the disposer (and remove its knockout plug on a new install) and the air gap. | Clean the filter, check the drain hose for kinks or clogs, clear the disposer (and remove its knockout plug on a new install) and the air gap. | Try it yourself |
| F9E2Call a pro | Drain motor error.Check the disposer and drain for clogs and straighten the drain hose. Cycle power; if it returns, call for service. | Check the disposer and drain for clogs and straighten the drain hose. Cycle power; if it returns, call for service. | Call a pro |
| F8E4Call a pro | Water in the base (the float switch tripped) — often a leak or excessive suds.Turn off the water supply. Check connections and the drip tray, avoid dish soap. If the dishwasher was professionally installed, call for service. | Turn off the water supply. Check connections and the drip tray, avoid dish soap. If the dishwasher was professionally installed, call for service. | Call a pro |
| F8E5Call a pro | Fill valve stuck open.Turn off the water to the dishwasher, press Cancel once and keep the door closed — then call for service. | Turn off the water to the dishwasher, press Cancel once and keep the door closed — then call for service. | Call a pro |
| F8E2Call a pro | Fill valve electrical error.Check the inlet valve connection for leaks, cycle power; if it returns, call for service. | Check the inlet valve connection for leaks, cycle power; if it returns, call for service. | Call a pro |
| H2OTry it yourself | Not detecting water.Make sure the water supply is on and the supply hose isn't kinked, then press Start. | Make sure the water supply is on and the supply hose isn't kinked, then press Start. | Try it yourself |
| F6E3Try it yourself | Excessive suds.Scoop out the suds, add 2–3 tablespoons of vegetable oil and run a cycle with no detergent, then a cycle with detergent and no dishes. | Scoop out the suds, add 2–3 tablespoons of vegetable oil and run a cycle with no detergent, then a cycle with detergent and no dishes. | Try it yourself |
| F6E4Try it yourself | Water float switch.Level the dishwasher and cycle power. | Level the dishwasher and cycle power. | Try it yourself |
| F4E2, F4E3Call a pro | Heating system error.Disconnect power for 30 seconds. If the code returns, call for service. | Disconnect power for 30 seconds. If the code returns, call for service. | Call a pro |
| F7E2Call a pro | Wash motor error.Cycle power; if the code returns, call for service. | Cycle power; if the code returns, call for service. | Call a pro |
| FAE4 / F10E4, FAE5 / F10E5Call a pro | Diverter valve error (E4) or diverter leak (E5).Check for leaks under the dishwasher, cycle power or press Cancel twice. If it returns, call for service. | Check for leaks under the dishwasher, cycle power or press Cancel twice. If it returns, call for service. | Call a pro |
| F1E1, F1E2, F2E1, F2E2, F3E2, F6E1Call a pro | Control, keypad, communication or sensor (thermistor/OWI) errors.Disconnect power for 30 seconds. If the code returns, call for service. | Disconnect power for 30 seconds. If the code returns, call for service. | Call a pro |
Source: Maytag Product Help — dishwasher error codes (one article per code). Codes vary by model — check your owner's manual.
| Code | What it means | Try first | DIY or pro? |
|---|---|---|---|
| F4E3Try it yourself | Restricted airflow — the lint screen or vent is clogged, or the vent is crushed, kinked or has too many turns.Clean the lint screen, check the vent run and outside hood. If it persists, have the whole vent cleaned. | Clean the lint screen, check the vent run and outside hood. If it persists, have the whole vent cleaned. | Try it yourself |
| F4E4Try it yourself | Low or no line voltage — the heater can't turn on.Check both breakers (electric dryers need 240 V on a separate 30-amp circuit) and the power cord; call an electrician if needed. | Check both breakers (electric dryers need 240 V on a separate 30-amp circuit) and the power cord; call an electrician if needed. | Try it yourself |
| F4E1Call a pro | Heater system — the heater or heater relays.Turn off the breaker for 1 minute, restart on Timed Dry. If it returns, call for service. | Turn off the breaker for 1 minute, restart on Timed Dry. If it returns, call for service. | Call a pro |
| F3E2, F3E5Try it yourself | Moisture sensor — five loads in a row dried without sensor data.Level the dryer and dry fuller loads on an Automatic cycle. Power cycle if it continues. | Level the dryer and dry fuller loads on an Automatic cycle. Power cycle if it continues. | Try it yourself |
| F3E1, F3E3Call a pro | Exhaust or inlet thermistor.Power cycle for 1 minute and run a Timed Dry cycle. If it returns, call for service. | Power cycle for 1 minute and run a Timed Dry cycle. If it returns, call for service. | Call a pro |
| F7E1Call a pro | Motor system — motor, control or wiring.Power cycle for 1 minute. If it returns, call for service. | Power cycle for 1 minute. If it returns, call for service. | Call a pro |
| F1E1, F1E3, F1E4, F1E5, F2E1, F2E2, F6E1Call a pro | Control unit, keypad or communication error.Power cycle at the breaker and run a Timed Dry cycle. If the code comes back, call for service. | Power cycle at the breaker and run a Timed Dry cycle. If the code comes back, call for service. | Call a pro |
Source: Maytag Product Help — dryer error codes (one article per code). Codes vary by model — check your owner's manual.
| Code | What it means | Try first | DIY or pro? |
|---|---|---|---|
| F9 E1Try it yourself | Drain is taking longer than expected.Check the drain hose and standpipe, and use HE detergent. | Check the drain hose and standpipe, and use HE detergent. | Try it yourself |
| F5 E2Try it yourself | The door isn't locking properly.Clear anything blocking the door and close it completely. | Clear anything blocking the door and close it completely. | Try it yourself |
| Sud, SdTry it yourself | Too many suds.Use the right amount of HE detergent. | Use the right amount of HE detergent. | Try it yourself |
| IntTry it yourself | The cycle was paused or canceled — the washer may take 20–30 minutes to stop and drain.Wait, then press Pause/Cancel twice and Power once to clear it. | Wait, then press Pause/Cancel twice and Power once to clear it. | Try it yourself |
| F7 E1Call a pro | Motor speed sensing error.Make sure the washer isn't overloaded. A repeat code needs a technician. | Make sure the washer isn't overloaded. A repeat code needs a technician. | Call a pro |
Source: Maytag Product Help — error codes in front load washers. Codes vary by model — check your owner's manual.
Common Problems
Six Maytag Symptoms and the Usual Suspects
These pairings follow from how Maytag appliances are generally built, and your technician confirms the real cause on your own unit before quoting anything.
Washer stops with water still in the drum
- Likely causes
- A clogged pump filter, a drain pump that has failed, a kinked or blocked drain hose, a lid or door lock that won't confirm
- What we check
- We clear the pump inlet, test pump voltage and windings, follow the hose to the standpipe and watch the lock and motor during a drain and spin test.
Dryer takes two or three cycles to finish a load
- Likely causes
- A restricted or crushed vent, a weak heating element, a gas igniter or valve coil that is failing, a cycling thermostat cutting out early
- What we check
- We measure airflow at the outdoor hood, test every part in the heating circuit and time how long the dryer actually produces heat.
Refrigerator compartment warms up while the freezer stays cold
- Likely causes
- A defrost fault that has iced the evaporator, a stalled evaporator fan, an air damper stuck closed
- What we check
- We look at the frost on the coil, test the defrost heater, sensor and fan motor and confirm the damper moves freely.
Dishwasher leaves a gritty film behind
- Likely causes
- A packed filter, spray arm holes clogged with debris, low water fill, a circulation pump losing pressure
- What we check
- We clean and inspect the filter and spray arms, measure how much water enters the tub and run the pump to see whether pressure holds.
Gas oven bakes unevenly or never reaches temperature
- Likely causes
- A weak igniter that opens the gas valve too slowly, a drifting temperature sensor, a worn door gasket, a burner that needs adjustment
- What we check
- We measure igniter current, check sensor resistance against a test thermometer, inspect the gasket and watch the flame during a full bake.
Over-the-range microwave runs but food stays cold
- Likely causes
- A failed magnetron, a bad high-voltage diode or capacitor, a faulty door switch, a control board relay that isn't passing power
- What we check
- We safely discharge the high-voltage circuit, test each component and the door switches in turn and confirm the relay is doing its job.
Arvada Homes
Where Arvada Homes Shape a Maytag's Workload
A few real features of this city influence how Maytag appliances here are installed, used and repaired.
Mid-century houses with modern machines
The city grew quickly as a Denver suburb after World War II, and many neighborhoods date from the 1950s through the 1970s. Kitchens and laundry areas in homes of that age were laid out long before today's appliances, so a newer Maytag may sit in a tight cutout or a basement corner it was never designed for. Those spaces can mean long dryer vent runs, cramped water connections and limited airflow around a refrigerator. Your technician checks the installation along with the machine, since the setting is sometimes part of the fault.
Historic homes around Olde Town
Olde Town Arvada is the historic district and the heart of the city, and older houses there have often been updated room by room. A Maytag dishwasher or range in one of these kitchens may be wired, plumbed or vented in ways that reflect several rounds of remodeling. We take care with finished cabinetry and older floors, and we look at supply lines, drain connections and outlets before blaming the appliance itself. That habit keeps a simple fix from turning into a second visit.
Gas burners above 5,000 feet
Much of the city sits at roughly 5,300 to 5,500 feet, and the thinner air at that height changes how gas mixes and burns. A Maytag gas range, oven or dryer that isn't set up properly for the elevation can show lazy flames, slow heating or burners that struggle to stay lit. When we work on a gas appliance, we watch the flame and the ignition sequence under real conditions, not just at a glance. If something looks wrong, we explain what we see before recommending any part.
Know Your Maytag
How We Keep a Maytag Repair on Target
Maytag repair that Arvada households can trust comes down to a few working habits that keep the diagnosis grounded and the right part on the truck.
The tag tells the real story
Your Maytag's model and serial label identifies the exact build, which matters because two machines that look identical can carry different boards, motors or pumps. The label usually sits inside a refrigerator compartment, around a washer lid or door opening, along a dishwasher tub edge or near an oven frame. A quick photo of it when you book helps us prepare. We order parts from that number, never from appearance.
Control boards run the show
Newer Maytag appliances manage their cycles through electronic controls, touch panels and, on some models, app connectivity. When a board misreads a sensor or loses a signal, the symptom can look like a mechanical failure. We test the sensors, harness connections and outputs around the board before condemning it, since a board is often one of the pricier parts on the machine. Connected features rarely change the repair itself, but they can add useful clues.
A code often names a process
Some Maytag error codes point to a single component, while others report only that a fill, drain or heat-up took longer than expected. A slow-fill code, for instance, could come from a closed supply valve, a kinked hose or a failing inlet valve. We treat each code as the starting point of a test sequence, not as a parts list. That approach saves you from paying for parts that were never broken.
Genuine parts that are easy to find
Maytag parts are generally well stocked, which helps keep repairs moving instead of stalling for weeks. We install genuine OEM parts matched to your model and serial number, so the fit and performance match what the machine was built with. Same-day service is often available, though we can't promise it on any given day. Every repair carries our 90-day parts and labor warranty.
Repair or Replace?
Fix This Maytag, or Put the Money Toward a New One?
The NAHB lifespan figures beside this section give a rough idea of how long each appliance type tends to last, and they make a reasonable starting point, though they describe averages and not your particular machine. For a Maytag with one failed part and a sound cabinet, tub and drive, repair usually makes good sense, especially since parts are generally easy to source. A new pump, igniter, belt or sensor can return years of ordinary service for far less than replacement. Your technician will tell you plainly what failed, what the fix costs and how the rest of the appliance looks.
The balance tips the other way when an aging refrigerator needs sealed-system work, when a washer's tub or bearings are worn late in life, or when several problems surface at the same time. Energy use matters too, since a much older refrigerator or washer may cost more to run each month than a newer one would. We'll give you a firm repair price so you can compare it honestly with the price of a new machine and installation. If replacing makes more sense, we'll say so and leave the decision to you.
Typical lifespan by appliance
| Refrigerator | ~13 yrs |
|---|---|
| Washer | ~10 yrs |
| Dryer | ~13 yrs |
| Dishwasher | ~9 yrs |
| Oven | ~13–15 yrs |
| Range & Stove | ~13–15 yrs |
| Microwave | ~9 yrs |
Source: NAHB study of home component life. Any brand; real life varies with use and care.
Google Reviews
What Our Customers Say
5.0Every review on Google is five stars.
“Nick was very knowledgeable and provided great service. He arrived on time and was very professional. I would definitely use him again for any future service.”
Marc S.July 2026 · Google “My GE refrigerator stopped cooling shortly after we moved to Superior. We wanted to support a local company, so we called PointLine Appliance Repair. Nick came out the same day, fixed the fridge on the spot, and the price was very reasonable. Super friendly, professional, and easy to work with. We’ll definitely call them again if we ever need another appliance repaired. Highly recommend!”
Alyssa M.July 2026 · Google “Very great and efficient diagnosis. Even though the result will be an appliance replacement, he was very knowledgeable and able to walk me thoroughly through the problem. Fast, same day service on the weekend was incredible.”
Erin C.June 2026 · Google
Membership
PointLine Care Club
One service call is $85. For $99 a year, every service call is free.
- Free service calls all year — no $85 fee
- 1 free maintenance visit a year
- 10% off labor on every repair
$99/ year
One household · renews yearly · cancel anytime before renewal
Property manager or landlord? See our Property Care Club →
Arvada Service Area
Maytag Repair Across Arvada
ZIP codes 80002, 80003, 80004, 80005, 80007, 80033 and the neighboring communities we serve every week.
Managing rentals? See the Property Care Club.
FAQ
Maytag Questions From Local Homeowners
Straight answers for Maytag owners in Arvada.
A code just appeared on my Maytag display. Should I keep running it?
Not until you know what it means. Look it up in the tables on this page; if it's marked as something you can try yourself, follow that step, and if it points to a pro or keeps returning, stop using the machine and book a visit.
Can you repair a Maytag with Wi-Fi or touch controls?
Yes. We test the sensors, wiring and outputs around the control board first, so the board is replaced only when it is truly the faulty part.
Do you work on built-in dishwashers and over-the-range microwaves?
Yes. We repair Maytag dishwashers set into cabinetry and microwaves mounted above the range, and we take care to protect counters, cabinets and finished surfaces while we work.
What parts go into my Maytag?
Only genuine OEM parts. We match them to your model and serial number, and the repair carries a 90-day parts and labor warranty.
How soon can a technician get to my house?
Often the same day, though we can't guarantee it. Our office in Superior is close by, and booking online or calling or texting (720) 285-3573 gets you the earliest opening.
Which ZIP codes do you serve in Arvada?
We cover 80002, 80003, 80004, 80005 and 80007, plus the shared 80033 ZIP code.
Is PointLine connected to Maytag?
No. We are an independent, family-owned repair company with no affiliation with Maytag, and we answer only to you.
Is your Maytag stuck halfway through the job?
Book online or call or text (720) 285-3573 for a $85 diagnostic credited toward the repair, a firm quote before work begins and the option of PointLine Care Club coverage at $99 a year.
PointLine Appliance Repair is an independent repair company, not affiliated with Maytag.