Local • Family-Owned
Whirlpool Repair in Broomfield, CO
Whirlpool refrigerators, washers, dryers, dishwashers and ranges tested in your Broomfield home, with a firm price before any part changes hands.
We repair every Whirlpool appliance
- $85 DiagnosticCredited toward your repair
- 90-Day WarrantyParts & labor
- Open 24/7Same-day service often available
- Local & Family-OwnedBased in Superior
Whirlpool Repair • Broomfield
Straight Answers for the Whirlpool Machines You Use Every Day
Broomfield homeowners who book Whirlpool repair with PointLine are served from our single office at 2600 S Rock Creek Pkwy #103 in Superior, just past the city line. We're an independent, family-owned company, so the people who answer your call or text are the same people who care how the repair holds up months later. Most of the city is a short drive along US-36 from our door. Every visit begins with a $85 diagnostic that counts toward the repair if you decide to move ahead.
Whirlpool ends up in nearly every kind of house, from an established kitchen with a coil-top range to a newer build with a French-door refrigerator and a hushed dishwasher. That reach comes with a catch: Whirlpool shares designs and components across a huge number of models, so one symptom can have several sources. A washer that won't drain might need a pump, a cleared filter, a new lid lock or attention at the control board. Your technician tests first, names the failed part, and gives you a firm quote, aiming for one correct repair instead of a string of hopeful ones.
Whirlpool Appliances
The Twelve Whirlpool Appliances We Service
Here is how each Whirlpool appliance tends to act when a part wears out, and where our testing begins.
Whirlpool Refrigerator
A Whirlpool refrigerator that runs warm more often has a frosted evaporator coil, a stalled fan or a defrost fault than a dying compressor. We check airflow, the defrost heater and sensor, the condenser fan and the start components before the sealed system enters the conversation.
Whirlpool refrigerator repair in BroomfieldWhirlpool Freezer
Upright and chest Whirlpool freezers usually ask for help through heavy frost, a door that won't seal or a cabinet that hums without getting cold. We test the door gasket, the defrost parts on frost-free models, the condenser and the temperature control.
Whirlpool freezer repair in BroomfieldWhirlpool Ice Maker
An empty bin or small, hollow cubes often trace to a water inlet valve, a frozen fill tube, a clogged filter or the ice maker module itself. We look at the water pressure at the valve, the freezer temperature and how the module runs its harvest cycle.
Whirlpool ice maker repair in BroomfieldWhirlpool Washer
Whirlpool top-loaders and front-loaders commonly stall on drain, leak at a hose or door boot, or refuse to spin with a load still inside. We look at the drain pump and filter, the lid or door lock, the drive components and the speed sensor before quoting.
Whirlpool washer repair in BroomfieldWhirlpool Dryer
A Whirlpool dryer that tumbles without heat may have an open thermal fuse or failed element on electric models, or a weak igniter or gas valve coils on gas models. We also check the vent, because restricted exhaust is often why those parts gave out.
Whirlpool dryer repair in BroomfieldWhirlpool Dishwasher
Standing water, cloudy glasses and a dripping door usually point to a clogged filter, a tired drain pump, a worn door gasket or a failing inlet valve. We run a cycle, watch the fill and drain, and inspect the spray arms and seals.
Whirlpool dishwasher repair in BroomfieldWhirlpool Oven
An oven that heats slowly, runs off temperature or won't bake at all points toward a bake element, a gas igniter, a temperature sensor or the control. We measure resistance, watch the igniter's current draw and compare the real cavity temperature with the setting.
Whirlpool oven repair in BroomfieldWhirlpool Wall Oven
Whirlpool wall ovens add cooling fans, door latches and snug cabinet fits to the usual heating parts. We test the elements, sensors, self-clean lock and cooling fan, and we cover the nearby cabinetry if the oven needs to be slid out.
Whirlpool wall oven repair in BroomfieldWhirlpool Range & Stove
A range pairs a cooktop with an oven, so one complaint can live in either half or in the controls they share. We check the surface burners or elements, the oven's heat source and sensor, and the switches and board that tie them together.
Whirlpool range & stove repair in BroomfieldWhirlpool Cooktop
Gas burners that click without lighting and glass-top zones that stay cold are the usual reasons to call. We check spark modules, igniters, burner caps and gas flow on gas models, and switches, elements and limiters on electric ones.
Whirlpool cooktop repair in BroomfieldWhirlpool Microwave
If your Whirlpool microwave runs without heating, sparks or doesn't respond to the keypad, it needs careful testing because of the high-voltage parts inside. We check the door switches, magnetron, diode and capacitor, and on over-the-range models the vent fan and lights.
Whirlpool microwave repair in BroomfieldWhirlpool Range Hood
A hood that has gone silent, rattles or barely pulls smoke usually has a failed fan motor, a bad switch, grease-packed filters or a damper stuck in the duct. We test the motor and controls and follow the duct path to the outside.
Whirlpool range hood repair in Broomfield
Error Codes
What Your Whirlpool Display Is Reporting
The tables below reproduce the code lists Whirlpool publishes on its own support pages, arranged by appliance so you can find yours quickly. Codes marked "try it yourself" usually have a safe, simple step such as clearing a filter or restarting the cycle, while those marked "call a pro" point to parts or wiring that belong in a technician's hands.
| Code | What it means | Try first | DIY or pro? |
|---|---|---|---|
| F9E1Try it yourself | Long drain — the dishwasher isn't draining.Clean the filter, check the drain hose for kinks or clogs, clear the disposer (and remove its knockout plug on a new install) and the air gap. | Clean the filter, check the drain hose for kinks or clogs, clear the disposer (and remove its knockout plug on a new install) and the air gap. | Try it yourself |
| F9E2Call a pro | Drain motor error.Check the disposer and drain for clogs and straighten the drain hose. Cycle power; if it returns, call for service. | Check the disposer and drain for clogs and straighten the drain hose. Cycle power; if it returns, call for service. | Call a pro |
| F8E4Call a pro | Water in the base (the float switch tripped) — often a leak or excessive suds.Turn off the water supply. Check connections and the drip tray, avoid dish soap. If the dishwasher was professionally installed, call for service. | Turn off the water supply. Check connections and the drip tray, avoid dish soap. If the dishwasher was professionally installed, call for service. | Call a pro |
| F8E5Call a pro | Fill valve stuck open.Turn off the water to the dishwasher, press Cancel once and keep the door closed — then call for service. | Turn off the water to the dishwasher, press Cancel once and keep the door closed — then call for service. | Call a pro |
| F8E2Call a pro | Fill valve electrical error.Check the inlet valve connection for leaks, cycle power; if it returns, call for service. | Check the inlet valve connection for leaks, cycle power; if it returns, call for service. | Call a pro |
| H2OTry it yourself | Not detecting water.Make sure the water supply is on and the supply hose isn't kinked, then press Start. | Make sure the water supply is on and the supply hose isn't kinked, then press Start. | Try it yourself |
| F6E3Try it yourself | Excessive suds.Scoop out the suds, add 2–3 tablespoons of vegetable oil and run a cycle with no detergent, then a cycle with detergent and no dishes. | Scoop out the suds, add 2–3 tablespoons of vegetable oil and run a cycle with no detergent, then a cycle with detergent and no dishes. | Try it yourself |
| F6E4Try it yourself | Water float switch.Level the dishwasher and cycle power. | Level the dishwasher and cycle power. | Try it yourself |
| F4E2, F4E3Call a pro | Heating system error.Disconnect power for 30 seconds. If the code returns, call for service. | Disconnect power for 30 seconds. If the code returns, call for service. | Call a pro |
| F7E2Call a pro | Wash motor error.Cycle power; if the code returns, call for service. | Cycle power; if the code returns, call for service. | Call a pro |
| FAE4 / F10E4, FAE5 / F10E5Call a pro | Diverter valve error (E4) or diverter leak (E5).Check for leaks under the dishwasher, cycle power or press Cancel twice. If it returns, call for service. | Check for leaks under the dishwasher, cycle power or press Cancel twice. If it returns, call for service. | Call a pro |
| F1E1, F1E2, F2E1, F2E2, F3E2, F6E1Call a pro | Control, keypad, communication or sensor (thermistor/OWI) errors.Disconnect power for 30 seconds. If the code returns, call for service. | Disconnect power for 30 seconds. If the code returns, call for service. | Call a pro |
Source: Whirlpool Product Help — dishwasher error codes (one article per code). Codes vary by model — check your owner's manual.
| Code | What it means | Try first | DIY or pro? |
|---|---|---|---|
| F4E3Try it yourself | Restricted airflow — the lint screen or vent is clogged, or the vent is crushed, kinked or has too many turns.Clean the lint screen, check the vent run and outside hood. If it persists, have the whole vent cleaned. | Clean the lint screen, check the vent run and outside hood. If it persists, have the whole vent cleaned. | Try it yourself |
| F4E4Try it yourself | Low or no line voltage — the heater can't turn on.Check both breakers (electric dryers need 240 V on a separate 30-amp circuit) and the power cord; call an electrician if needed. | Check both breakers (electric dryers need 240 V on a separate 30-amp circuit) and the power cord; call an electrician if needed. | Try it yourself |
| F4E1Call a pro | Heater system — the heater or heater relays.Turn off the breaker for 1 minute, restart on Timed Dry. If it returns, call for service. | Turn off the breaker for 1 minute, restart on Timed Dry. If it returns, call for service. | Call a pro |
| F3E2, F3E5Try it yourself | Moisture sensor — five loads in a row dried without sensor data.Level the dryer and dry fuller loads on an Automatic cycle. Power cycle if it continues. | Level the dryer and dry fuller loads on an Automatic cycle. Power cycle if it continues. | Try it yourself |
| F3E1, F3E3Call a pro | Exhaust or inlet thermistor.Power cycle for 1 minute and run a Timed Dry cycle. If it returns, call for service. | Power cycle for 1 minute and run a Timed Dry cycle. If it returns, call for service. | Call a pro |
| F7E1Call a pro | Motor system — motor, control or wiring.Power cycle for 1 minute. If it returns, call for service. | Power cycle for 1 minute. If it returns, call for service. | Call a pro |
| F1E1, F1E3, F1E4, F1E5, F2E1, F2E2, F6E1Call a pro | Control unit, keypad or communication error.Power cycle at the breaker and run a Timed Dry cycle. If the code comes back, call for service. | Power cycle at the breaker and run a Timed Dry cycle. If the code comes back, call for service. | Call a pro |
Source: Whirlpool Product Help — dryer error codes (one article per code). Codes vary by model — check your owner's manual.
| Code | What it means | Try first | DIY or pro? |
|---|---|---|---|
| F9 E1Try it yourself | Drain is taking longer than expected (usually over 8 minutes).Check the drain hose for kinks or clogs and make sure you use HE detergent — excess suds slow draining. | Check the drain hose for kinks or clogs and make sure you use HE detergent — excess suds slow draining. | Try it yourself |
| F8 E1, LO FLTry it yourself | Low water flow into the washer.Turn the hot and cold supply valves fully open and check the fill hoses for kinks. | Turn the hot and cold supply valves fully open and check the fill hoses for kinks. | Try it yourself |
| F5 E2Try it yourself | The door isn't locking properly.Make sure nothing blocks the door and it closes completely, then clear the code. | Make sure nothing blocks the door and it closes completely, then clear the code. | Try it yourself |
| Sud, SdTry it yourself | Too many suds.Use HE detergent in the right amount; a restricted drain hose can also cause it. | Use HE detergent in the right amount; a restricted drain hose can also cause it. | Try it yourself |
| F7 E1Call a pro | Motor speed sensing error — the motor can't reach the right speed.Check the washer isn't overloaded. If the code returns, the motor system needs a technician. | Check the washer isn't overloaded. If the code returns, the motor system needs a technician. | Call a pro |
Source: Whirlpool Product Help — error codes in front load washers. Codes vary by model — check your owner's manual.
| Code | What it means | Try first | DIY or pro? |
|---|---|---|---|
| Flashing "F" codes (F3 E1, F3 E2, F4 E1, F6 E1, F8 E1…)Call a pro | A fault detected by the control.Turn off the breaker or unplug for 1 minute, restore power and make sure cooling is on. If the F code comes back, call for service. | Turn off the breaker or unplug for 1 minute, restore power and make sure cooling is on. If the F code comes back, call for service. | Call a pro |
| POTry it yourself | Power outage — power was off and the freezer warmed to 18°F or higher.Check your food, then confirm the alert on the control panel. | Check your food, then confirm the alert on the control panel. | Try it yourself |
| Temperature alarmCall a pro | The refrigerator rose above 48°F or the freezer above 15°F for more than 1½ hours.Make sure the doors close and nothing blocks the vents. If temperatures don't recover, call for service. | Make sure the doors close and nothing blocks the vents. If temperatures don't recover, call for service. | Call a pro |
| Door alarmTry it yourself | A door or drawer was left open for 2–5 minutes, or isn't closing fully.Close the doors, move bins or packages that block them, and check that the refrigerator is level. | Close the doors, move bins or packages that block them, and check that the refrigerator is level. | Try it yourself |
Source: Whirlpool Product Help — refrigerator error codes, blinking and flashing lights. Codes vary by model — check your owner's manual.
Common Problems
When a Whirlpool Misbehaves: Six Common Complaints
The causes listed are starting suspects based on how these machines are built; a meter and a test run on your own unit settle which one is real.
Fresh-food section warm while the freezer stays cold
- Likely causes
- Evaporator coil iced over from a defrost fault, a stopped evaporator fan, a blocked air passage
- What we check
- Frost pattern on the coil, fan operation, defrost heater continuity and sensor readings
Washer won't drain or spin
- Likely causes
- Clogged pump filter or hose, failed drain pump, faulty lid or door lock, worn drive parts
- What we check
- Pump and filter condition, lock function, motor and drive, and the fault history stored in the control
Dryer runs, but the clothes come out damp and cool
- Likely causes
- Open thermal fuse, burned-out heating element, weak gas igniter or valve coils, or a restricted vent
- What we check
- Continuity on fuses and element, igniter glow and gas valve action, airflow through the vent
Dishwasher leaves food behind or water in the tub
- Likely causes
- Clogged filter, blocked spray arms, weak circulation or drain pump, or a failing inlet valve
- What we check
- Filter and spray arms, fill volume, pump operation and the drain hose route
Oven won't heat or bakes unevenly
- Likely causes
- Failed bake element or igniter, a drifting temperature sensor, or a control fault
- What we check
- Element resistance, igniter current, sensor reading and actual cavity temperature against the setting
Ice maker stops making ice
- Likely causes
- Frozen fill tube, failed inlet valve, clogged filter, freezer running too warm, faulty module
- What we check
- Water pressure at the valve, filter flow, freezer temperature and a forced harvest test
Broomfield Homes
Three Local Facts a Whirlpool Technician Keeps in Mind
A few details about this city change what your technician looks for first on a Whirlpool call.
Established homes beside much newer ones
Broomfield started as a small town in the 1960s and saw its biggest growth in the 1990s and 2000s, so you'll find established homes right alongside much newer construction. An older kitchen may hold a Whirlpool that replaced an original appliance in an opening sized for a different era, while a newer home may carry a full matching suite with electronic controls. Each setup changes how we reach the unit, which parts fit and how a replacement would sit in the space. Reading the rating tag first keeps those differences straight.
Gas burners at about 5,300 to 5,400 feet
The city sits around 5,300 to 5,400 feet, where thinner air changes how gas burns. A Whirlpool gas range, cooktop, oven or dryer needs its burners set up correctly to hold a clean, steady flame. Flames that look yellow, lift off the burner or seem weak deserve attention, since they can point to setup, a dirty burner or a gas delivery problem. We look at the flame and the parts that shape it whenever we work on a gas appliance.
Two water supplies, one path to the ice bin
Broomfield gets its water from two sources: treated water purchased from Denver Water, plus Colorado-Big Thompson and Windy Gap water managed by Northern Water and treated at the city's own plant. Whichever reaches your tap, it still passes through a shutoff valve, supply line, filter and inlet valve before it becomes ice or dishwasher spray. Slow fills, small cubes and weak washing often begin somewhere along that path rather than deep inside the appliance. We check pressure, filters and valves before suspecting costlier parts.
Know Your Whirlpool
Know-How That Keeps a Whirlpool Repair From Repeating
When Broomfield homeowners schedule Whirlpool repair with us, four habits guide every visit, and each one begins before we remove a single screw.
The tag tells the real story
Whirlpool prints the model and serial number on a rating tag, usually inside the refrigerator compartment, around a washer lid or door opening, inside the dryer door, along the dishwasher tub edge, or near the oven frame behind the door or drawer. The serial number narrows down when a unit was built, which matters because internal parts can change within a single model. A photo of the tag sent when you book helps us arrive prepared.
Apps, touch panels and main boards
Some newer Whirlpool appliances link to an app over Wi-Fi and depend on a main control board to run cycles and monitor sensors. An app alert or a dark touch panel can implicate the board, but the trouble may just as easily sit in a sensor, a loose connector or the power feeding it. We test what goes into and out of a control before recommending one, since boards are among the pricier parts to replace.
A code is a report, not a parts order
Many Whirlpool codes say a process failed, such as a fill that ran long, a drain that never finished or an oven that missed its temperature. That message tells us which system to examine, and the culprit could be a valve, pump, hose, sensor or the control itself. Swapping the first part a search result suggests often leaves the actual fault in place.
Genuine parts, ordered by number
Because so many Whirlpool designs share components, parts are widely available, which often keeps the wait reasonable. We still order genuine OEM parts against your exact model and serial number, since a part that looks right can fit or read differently. Every repair carries our 90-day parts and labor warranty.
Repair or Replace?
Weighing One More Repair Against a New Whirlpool
The lifespan figures beside this section, drawn from an NAHB study, give a broad sense of how long each appliance type tends to serve, but they describe averages rather than the machine in your home. A Whirlpool that has been looked after may have plenty of service left, and often the fault turns out to be one part that is fairly priced and easy to get. After testing, you receive a firm quote, so you can set a known repair cost against the price of a comparable new appliance plus delivery and installation. That side-by-side comparison usually settles the question faster than age alone.
Energy use and the cost of parts should factor into the decision too. A refrigerator or freezer draws power every hour of the day, so the efficiency of a newer model can matter on a close call. Replacement deserves a hard look when a refrigerator's sealed system fails late in its life, when rust has reached a washer or dishwasher frame, or when one repair is likely to be followed soon by another. If we think your money is better spent on something new, we'll say so plainly.
Typical lifespan by appliance
| Refrigerator | ~13 yrs |
|---|---|
| Freezer | ~11 yrs |
| Washer | ~10 yrs |
| Dryer | ~13 yrs |
| Dishwasher | ~9 yrs |
| Oven | ~13–15 yrs |
| Wall Oven | ~13 yrs |
| Range & Stove | ~13–15 yrs |
| Microwave | ~9 yrs |
Source: NAHB study of home component life. Any brand; real life varies with use and care.
Google Reviews
What Our Customers Say
5.0Every review on Google is five stars.
“My LG washer stopped draining. Nick quickly diagnosed the problem and replaced the drain pump. The repair was completed the same day and everything is working great again. Professional service and fair pricing. Highly recommend!!!”
Victoria M.June 2026 · Google “This is a small owner-operated business, which is a big bonus as pricing is much more reasonable than using the chains or PE owned companies. Nick was accommodating, and installed a new evaporator fan in my GE Cafe fridge/freezer quickly and correctly. Highly recommend.”
Aaron F.July 2026 · Google “Nick was great. Quickly narrowed down our likely washer problem and got the part ordered with deposit. Quick install and had washer working within few hours once part arrived. Great communication throughout. Would definitely use again!”
Nathan H.August 2026 · Google
Membership
PointLine Care Club
One service call is $85. For $99 a year, every service call is free.
- Free service calls all year — no $85 fee
- 1 free maintenance visit a year
- 10% off labor on every repair
$99/ year
One household · renews yearly · cancel anytime before renewal
Property manager or landlord? See our Property Care Club →
Broomfield Service Area
Whirlpool Repair Across Broomfield
ZIP codes 80020, 80023, 80021 and the neighboring communities we serve every week.
Managing rentals? See the Property Care Club.
Other brands in Broomfield
Whirlpool Repair Guides
FAQ
What Broomfield Whirlpool Owners Ask Us
Straight answers for Whirlpool owners in Broomfield.
Do you work for Whirlpool?
No. PointLine is an independent, family-owned company and has no connection to Whirlpool. We repair Whirlpool appliances with genuine OEM parts, but Whirlpool plays no part in our business or our pricing.
My Whirlpool is showing an error code. Should I keep using it?
Look the code up in the tables on this page first, and stop using the appliance if it's marked for a pro or involves water, heat or gas. If a simple step clears it and it returns, note the code and when it appeared, then share that when you book.
Can you repair a Whirlpool with Wi-Fi features or one built into cabinets?
Yes, we work on connected Whirlpool models as well as built-in dishwashers, wall ovens and over-the-range microwaves. App alerts are a useful clue, but we confirm the fault with hands-on testing.
Will you install genuine Whirlpool parts?
Yes, we install genuine OEM parts matched to your model and serial number.
How quickly can a technician come out to my home?
Same-day service is often available, but we can't guarantee it on any given day. Booking early and sending a photo of the rating tag helps us plan the visit.
Which Broomfield ZIP codes do you serve?
We serve 80020 and 80023, along with the shared 80021 ZIP code. Our Superior office keeps most of the city a short drive away.
What does the first visit cost?
The diagnostic is $85, credited toward the repair if you go ahead, and you approve a firm quote before any work starts. Households that want ongoing coverage can join the PointLine Care Club for $99 a year.
Is a Whirlpool throwing off your week?
Call or text (720) 285-3573 or book online to set up a $85 diagnostic, credited toward the repair and followed by a firm quote before any work begins.
PointLine Appliance Repair is an independent repair company, not affiliated with Whirlpool.